Jump to content
SAU Community

Vicroads And Bpay...

htial

By htial,
in Victoria

 Share

Recommended Posts

htial Grand Master

htial

Posted
Posted

A few weeks ago I got my Licence Renewal and about a week after that I logged into my internet banking and paid it... ...Come to Monday just gone and I get pulled over for what I believe was not giving way to a police car who was doing a U-turn in front of me where I was coming out of a side street and doing a left turn... ...As far as I know I have the right of way in that situation... ...He didn't have his lights on and had to slam his breaks on to avoid hitting me... ...Crises everted and I drive on... ...About 300m down the road his lights come on and I have to drive a bit of a way to get past some parked cars and a bus and he hits the noise too...

Now I think this was my one and only mistake here because when he asked me if I knew why he stopped me I said, "Because you failed to give way while doing a U-turn and have stopped me to apologise to me?"...

He didn't say anything and just asked for my licence... ...I gave it to him and he pointed to the date... ...which was about 7 days past it's expiry... ...So I pull out the renewal form which I wrote down the Bpay code on but forgot to put down the date I paid it... ...And he said that it isn't acceptable and when back to his car for a bit and then told me that I don't have a licence... ...And so today I get the Infringement Notice in the mail...

Now my question is... ...Has anyone ever had trouble with Bpay and VicRoads, or the Police, when it comes to Licence Renewal???...

Link to comment
https://www.sau.com.au/forums/topic/270201-vicroads-and-bpay/
Share on other sites
gdogzgtr Proficient

gdogzgtr

Posted
Posted

Mate this tpye of thing happens quite often generally with registrations that are paid on expiriy date. I pull over lots of cars that come up unregistered and they have paid rego by b-pay and obviously vic roads have not processed it. I would also issue fine in that and this case and I just explain to send in copy of renewal, b-pay receipt details to civic compliance on stat dec and fine will be withdrawn.

That way I am covered because records show unreg/unlic and as long as rego/lic paid then easy enough for fine to get withdrawn.

jakez88 Veteran

jakez88

Posted
Posted

just take it up with vicroads mate. get in contact with them or just go down there and tell them what has happened. i'm pretty sure they should work it out and then you or they could fix up the thing with the infringement. i just paid for my full license through bpay and it went through all good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • GTSBoy
      R34 Skyline Sunroof Won't Tilt/Vent

      By GTSBoy · Posted

      Something's broken.
    • PranK
      Shoota's R33 GT-R RB30/26

      By PranK · Posted

      It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...