Jump to content
SAU Community

Recommended Posts

i turned the car off for a good 10 mins, then started it again and got off down the highway...the light stayed off for about 5 mins, then came back on again...with the r33 system having electronic actuators, doesnt it set itself to a centralised position and stop doing anything when it detects a problem?

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4599465
Share on other sites

Do you have an after market steering wheel installed? If you do, then theres a chance that the after market boss kit isn't HICAS compilable that or the HICAS sensor in the boss kit isn't connected properly.

This happens in my car.

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4599530
Share on other sites

I do have an aftermarket wheel on, HKS boss kit. it hasn't done it to me before, and after pulling in at Mittagong for about half an hour, it didn't do it again all the way back to Canberra. I'll pull all the plugs out and make sure they're clean of dirt etc, might pull the wheel off too and do the same.

Thanks for the input tho :P

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4599854
Share on other sites

A lock bar is generally around $200 + install and then you would need to get a wheel alignment.

Plus you need to pull the Hicas bulb in the dash or it stays on permanently.

The other option is the Tomei Hicas lock kit which has shims and an electronic gizmo to fool the ECU into thinking Hicas is still functioning, currently around $185 + postage on Ebay.

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4600637
Share on other sites

I always thought the pressure was required to keep the rear rack centred, and hence the need for a hard lock if you disable it.

I removed all the crap from mine - lines etc and lost about 20 kg of highly expensive junk as well as creating extra ps fluid capacity. Was going to fit a shorter R33 pump but it's well down the list of things to do.

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4604294
Share on other sites

I was going to have all my hicas stuff removed when i had my engine out...but the guy "FORGOT" so instead he put in a lock off whatever it is. with a lockbar then unplugged the solinoid to stop warning lights...but forgot the speed sensor which made more lights come on....><

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4607177
Share on other sites

I was going to have all my hicas stuff removed when i had my engine out...but the guy "FORGOT" so instead he put in a lock off whatever it is. with a lockbar then unplugged the solinoid to stop warning lights...but forgot the speed sensor which made more lights come on....><

Please tell me this guy had nothing to do with your engine removal/fitting...

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4607560
Share on other sites

Please tell me this guy had nothing to do with your engine removal/fitting...

>< It's being checked over by someone who's work i trust currently so he will pick up on anything else that has been forgotten...but in the most part the only problem with the engine ive had was the accessory belt needed tightening and a few old wired snapped. But the car runs smooth as a untuned GTR does...

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4609717
Share on other sites

Troy, seeing as I sold you the car, I will clarify a few things to save you and a few other people some time.

For the record you have a HKB bosskit installed in the car fitted to a GKtech wheel, the bosskit inwhich is in your car is HICAS compatible. The problem you have found occuring is not infact related to steering wheel.

If you stick your head under the back end of the car you will notice that there is the KYB HICAS linkage system, carefully, and I repeat carefully remove all the plugs and give them a spray with contact cleaner or electrical contact cleaner, it is quite dirty under there I know, and 15+ years of driving im sure has clocked up alot of dirt,

The member who posted that the Hicas system throws a warning under movement of the rack ends is correct to an extent however it is highly unlikely that the rear end of the car would move enough to trip sensors, I should know I went over the car with a fine tooth comb before it went on the truck.

The light has come on with me driving only 3 times in the 2 and abit years I owned it, and I put it down to age, I can assure you nothing in the rear end is astray or in need or repair, however a safety check would be recommended for peiece of mind.

A more probable cause to the problem mate (having worked around many Hicas equipped cars over the years) Would be that a earth wire has come loose (which I suspect is the case) or Jax Quitfit f**ked it somehow when they did the balance on the tires.

I suggest jacking the rear end of the car up mate, and if you drop the 2 10mm bolts either side of the linkage it will swing down, there you will be faced with 2 21-23mm bolts holding the diff into the rear cradle, what I suggest checking is that the HICAS earth is still connected to the left bolt, if it isn't re-connect it, I dare say this is your problem!

Goodluck mate and keep me posted on the car, I do miss it alot!

Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4610984
Share on other sites

The member who posted that the Hicas system throws a warning under movement of the rack ends is correct to an extent however it is highly unlikely that the rear end of the car would move enough to trip sensors, I should know I went over the car with a fine tooth comb before it went on the truck.
I was only talking to John @ Trojan about this on Friday night.. One reason that was brought up is that if you have movement/play in your rear rackends. The Hicas throws warnings

It was only a noted suggestion as it was a coincidence we were just talking about it as my rear rackend wasn't in great shape (since replaced two days ago).

Edited by sfrizza
Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4611670
Share on other sites

Also it is worth noting that you should check the fluid and top up if necessary, even over-full if you wish, It sovled my problem first time it happened in the car!

From what i remember, the rear hicas resovouir needs to be topped up when the car is running as it drops a bit. If you top it up when it isnt on it could still drop below the minimum and trigger the warning light. Check every plug and as age was mentioned, check for snapped wires. It doesnt take much for years of little bits of road hitting a wire to one day just snap.

Hope its a quick fix for you once you find the problem :(

Edited by Helious
Link to comment
https://www.sau.com.au/forums/topic/270402-hicas-warning/#findComment-4611753
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...