Jump to content
SAU Community

Recommended Posts

Not much,

Still capable of sitting ppl at the back but depending how tall they are.

Well it's better then a Supra or RX7 back seat.

I have sat in the back seats of all 3 of them and the Skyline still better for leg room.

Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4600852
Share on other sites

Hey everyone, I'm new here, although I have always loved the skylines. Just wondering how much leg room in the back seats of these cars (R32, 33 and 34 models). If anyone can help me out, I would greatly appreciate it.

Thanks. :P

In scientific terms - none, almost none, and a little.

Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4601028
Share on other sites

The 34 coupe (GT-T/GT-R) is capable of holding a passenger and driver comfortably (im 6ft) and fit comfortably although when switching from my dad's Mitsubish Magna or my other car (Holden Commodore) i tend to notice a big difference and feel confined in the 34.

Although over time you get used to that feeling (give or take a couple of weeks) and you begin to like it...going back to the bigger cars makes you wonder what all the rest of the room is really for? :(

But if you have several passengers the 34 is horrible...i have taken a full car (5 people) and i will never do it again (in fact i never take anyone in the back at all), all the boys were over 6ft and it was just pure shit....not to mention the performance of the RB25DE declined immensley since it is a non turbo and could not cope with the extra weight.

From what i know the R33 has alot more leg room (well it feels so) and the 4 Door 34 has more room obviously since it has those extra doors. the 32 is like the 34 in terms of interior space.

Best room would be a 4 door version of any of the skylines or a 33 coupe model if your looking at 2 doors. Anyhow hope that helps out a bit...

Edit: Didn't read your thread with the rear leg room just assumed by the topic name. I would not get a 34 for the rear leg room!!!!! its terrible..you can fit a asian midget (or a baby) if your lucky fairly well....thats about it...

Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4601846
Share on other sites

had an r33 then an r34, friend had an r32

r33 coupe definitely has the most rear legroom out of the three...

but that's like saying getting punched in the nuts only slightly less painful as getting kicked.

Edited by Yo-Yo
Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4602135
Share on other sites

Yeah um the back seat of the R32 is good if you happen to be carting around Asian school girls, for everyone else, its EXTREMELY cramped (even in mine with GT-R seats).

In a R33, I could move my legs at least, but my head was still hitting the rear window (I'm 180cm), on the plus side, with 3 of us in there, we could go around corners without me spilling my beer :(

In terms of front seats, both have acres of room unless you happen to be a very fat person.

HR31 rear seat is somewhere in between a R32 and R33 for leg and body room.

HR31 4 door was reasonably comfy as long as I had my knees on either side of the driver seat when sitting behind it lol.

I try to strenuously avoid having back seat passengers in mine, its usually used to hold my CD wallet, random tools, bits of pipe, my club lock, hitchhiking spiders etc.

Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4602141
Share on other sites

I found it fine, its got more leg room behind compared to my dad's Mazda ute & my friends 180sx (man that car has like no room in the back...).

But its tiny compared to ur family cars like camry & commodores etc etc.

Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4602510
Share on other sites

Hey everyone, I'm new here, although I have always loved the skylines. Just wondering how much leg room in the back seats of these cars (R32, 33 and 34 models). If anyone can help me out, I would greatly appreciate it.

Thanks. :huh:

Dusn't matta! Us Blonds like to sit in da middle with a leg Eye-da side of da transmishun...

Link to comment
https://www.sau.com.au/forums/topic/270531-leg-room/#findComment-4602624
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...