Jump to content
SAU Community

Recommended Posts

hey guys im thinking of building an r31 slider but a few on hear say there shit to drift. is this true? is it worth me doing one or not.

does anyone slide one off these and can anyone compare with another car they have sliden.

if they are good whats the best few uprades to get em to hold slides. cheers

:dry:

Link to comment
https://www.sau.com.au/forums/topic/271049-how-does-the-r31-drift/
Share on other sites

hey guys im thinking of building an r31 slider but a few on hear say there shit to drift. is this true? is it worth me doing one or not.

does anyone slide one off these and can anyone compare with another car they have sliden.

if they are good whats the best few uprades to get em to hold slides. cheers

:sick:

mate they slide just fine Iv drifted em all dr30 to r34,and I reckon they are very underated,they do need a bit of work on the suspension but thats with any car,Iv just picked up a gtsx last week set up to drift and it slides mad,and best bet for handling go coilovers or if its an oz model springs+shock combo or do a s13 front end coversion,28m sway bars,nolthane bushes and a lsd that should get you started,theres nothing wrong with a 31 as a drift car,heaps of parts availble cheap,and any one who says there shit to drift cant drive for shit coz i reckon you get the best feel for the road out of 31,newer models have alot lighter steering,also my daily is a r31 shilo drift pig iv been driving it for 10 years!!

yea man thats it do a bit o work to suspension then the ol lines drift good for wat the are, im happy with my dr30, something differnt 2.. they are heavy but if ne thing learning to drift in one of em will only hone your skills, my mates 31, weldi chop springs, rb30 + T does damn well...

A couple of years back, I think in the first year of Drift Nationals, a gold HR31 was in the field sponsored by R31 House and I thought it went very well, it's only failing that I could see was the dill behind the wheel.

Compared to the talents of others on the day, it could have performed much better with a better steerer.

Just my humble opinion, from a spectator, not a drifter competitor.

Cheers, D

That gold Coupe was THE R31House Drifter, Shibata san PAID to ship it over here, and was treated quite poorly by the guys who organised to bring them over.

Picture027.jpg

31's slide damn good for the long, weighy bucket that they are, I know a bloke who started out with a stocker, a locker and a good seat, kicked the asses of a few higher powered, lighter weight cars.

Plenty of youtube action, Joel MacKerres, Chris Easton, Ev Daws

http://www.youtube.com/watch?v=r_0uAoX1amk

& we all love Fatz... *edit* (3min 25)

http://www.youtube.com/watch?v=Wr7reJKNUOY

Edited by B. J.

thanks heaps for the feed back guys i have owned one of these back in the day but didnt do much or any sliding with it. i drive an r33 now and slides well but for some reson thought it might be a good idea to build a drift pig track only car i can distroy tyres with.

on the subject at hand where is the best place to start looking for one ,i want the cheapest r31 s2 around. any tips on where to start looking.

also any specs on cams aproval what do i need to do to get it right for the track. cheers :D

thanks heaps for the feed back guys i have owned one of these back in the day but didnt do much or any sliding with it. i drive an r33 now and slides well but for some reson thought it might be a good idea to build a drift pig track only car i can distroy tyres with.

on the subject at hand where is the best place to start looking for one ,i want the cheapest r31 s2 around. any tips on where to start looking.

also any specs on cams aproval what do i need to do to get it right for the track. cheers :D

there is a guy up here that has a R31 that has a turboed RB30 in it i think he is looking for about 2000-2500 for it

89 R31 bid is at $900

http://cgi.ebay.com.au/nissan-skyline-gxe-...%3A1%7C294%3A50

we also got this one off ebay for $600 to build as a street car and a drift pig

hannahandblakespictures004.jpg

19052009245.jpg

Wouldn't an KHR31 be a better drifter as it has IRS as opposed to a live rear axle in the Oz produced & delivered car?

And it already has the RB DOHC engine & LSD.

Cheers, D

The IRS in the HR31 isnt much to write home about, very squatty and hard to get right for sliding, Easto was / is running an R33 rear cradle, but that takes a shitload of money and mods to do correctly, Decs has put one into an aus-spec & says he'll never do it again coming from a mechanical side of things.

Aus rear axle is reliable chuck in a spool, lock it up or even a KAAZ and away you go.

Finding a coupe (wouldnt suggest sliding a 4 door hardtop) for a fairly cheap price will be the hard part. Yes they came with a 20 but the redtops have seen better years, so you'll be headed towards a silvertop, 25 or something bigger anyway. If you're looking for a coupe to slide, it might be worthwile running around and trying to find one pre-modded in japan and leave it as track only, it'd be the cheapest way to get one.

at least with the Aus RB30 you can slap on an ebay spec turbo, intercooler kit and a good tune can get you 180-200rwkw which is plenty to get an R31 sideways.

*edit* - few pics

DSC_0121.JPG

DSC_0181.JPG

DSC_0503.JPG

DSC_0504.JPG

DSC_1890.JPG

DSC_1891.JPG

DSC1301.JPG

^ note the rear camber on the one in the background - R33 Rear cradle in AUS Spec R31

Edited by B. J.

R30s weigh pretty much same as a s13, 1100kg ish. DR30s weigh bit more like 1300kg top end models. but if 4 track rip the electrics, seats, trim and sound deadening out and back down 2 1100kgs or less (as ive done)...

have drifted both as well and (r31 rb30et, dr rb20det) found the dr easier to control. 4 me anyway..

Edited by OUTATIME
stock engine, soft coilovers, swaybars and castor rods, hd clutch and locker.

nice drifting with that setup dude. have u used an lsd for drifting how do u find the locker drifting. do u spin out much or not. and how come the soft coilovers i would have thought the harder the beter.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...