Jump to content
SAU Community

Recommended Posts

Ive heard alot of different opinions here about the r34 rb25 turbos. Upon inspecting both ive found the r34 turbo to have a steel rear wheel amongst other minor things. Now im aware of r33 rb25 std turbos not agreeing with higher boost levels due to the rear wheel letting go being ceramic. What are your opinions with boost and an r34 rb25 std turbo remembering that it has a steel rear wheel. Let me know your thoughts..

Edited by wallas

never heard or seen of a steel rear wheel on ER34 turbocharger

please double check and confirm

and even if it is steel rear wheel, the compressor will stilll run out of effiency and past its effiencny island

which in turn just dials heat into the intake charge, so steel or no steel, doesnt really help a lot, just means it wont fail from excessive shaft speed / heat

typically 12psi is the island / max spot of the compressor map - so any more, is more heat for little to no gain

i have to disagree with you about it not making power above 12psi. a mate of mine put his stock turbo'd 33 on the dyno and just started winding the boost up (aftermarket ecu obviously). started at 200kw at 13psi and the power kept rising until they stopped at 16psi whnere it was making 220kw. i also ran my stock turbo at 14/15psi for quite a while with no issues either, and it felt much more powerful than 11psi. i wound it back down one day and it felt much less powerful.... so i wound it back up.

as for the r34 turbo, they don't have steel wheels unless they have been highflowed. the series 1 r33 turbo has steel compressor wheels but they all have ceramic exhaust wheels. the r34 is a bigger turbo than the 33.

R33/R34 - basically idential in terms of thier limitations and so on.

R34 turbos are just newer, so will take 14psi 'longer', they will still fail and are still ceramic rear.

If yours has steel (test using a magnet) then its not a standard R34 item.

11-12psi is the limit, push it and it will die

i have to disagree with you about it not making power above 12psi. a mate of mine put his stock turbo'd 33 on the dyno and just started winding the boost up (aftermarket ecu obviously). started at 200kw at 13psi and the power kept rising until they stopped at 16psi whnere it was making 220kw. i also ran my stock turbo at 14/15psi for quite a while with no issues either, and it felt much more powerful than 11psi. i wound it back down one day and it felt much less powerful.... so i wound it back up.

as for the r34 turbo, they don't have steel wheels unless they have been highflowed. the series 1 r33 turbo has steel compressor wheels but they all have ceramic exhaust wheels. the r34 is a bigger turbo than the 33.

When i had my stock turbo tuned with pfc there was no difference in power between 10 -13psi just an increase in low end power. So my experiences will disagree but every car is different i guess.

but that could also come down to the tune, and if it was done on different days, etc.

i have seen pfc tunes where they have put out less power than stock ecu's for the simple fact of the tune is dodgy. i compared a dyno sheet from my stock ecu with that of a with a pfc and his made a few kw more than my car throughout the rev range until about 5500rpm where his pretty much flattened out but mine kept going until it hit the speed limiter and so i ended up making about 20kw more.

You also need to look at power/psi. So as mentioned.. efficiency.

Back to back dynos against a mates 33GTSt and mine, his made 5 morw rwkw with 5psi more boost. Exact same mods, bar his being Link tuned, and mine Stock ECU.

1kw per PSi doesnt feel like efficient power to me. Sounds like a whole lot of hot air :)

but that could be caused by other issues as well. crap tune, sad motor, etc. to compare different cars at different boosts is a bit pointless. but i know from seeing the evidence first hand on back to back dyno runs that there was a gain of 20kw by going from 12 to 16psi.

but then my car made 15kw more than 2 of my mates cars with the same mods, and another car with the same mods made pretty much the same power as me (was within 1kw)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
    • Got you mate. Check your email!
    • I see you've never had to push start your own car... You could save some weight right now...
    • Sounds good.  I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear?  If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific.  Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time. It will stick to the clear coat provided it has been appropriately scuffed/prepped first.  When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean?  So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time.  The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint.  So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear?  Life seems so much simpler if you prep, fill, primer, colour then clear.  There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal.  A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 
×
×
  • Create New...