Jump to content
SAU Community

Turbo Oil Feed For Single Conversion

leeroy_25
 Share

Recommended Posts

leeroy_25 Community Regular

leeroy_25

Posted
Posted

I am building an RB30/RB26 ad running a single turbo setup.. I have the series 1 block which does not have the oil feed in it for a turbo so was planning to take a feed from the oil pressure switch. What I noticed though is I think most the turbo takes a -4AN (1/4") bore fitting where as the oil switch is only 1/8"NPT Will I get sufficient oil for the turbo from here? Looking in side the turbo it seems the oil holes to the bearings are only very small but I want to be sure.. I guess I could open up the oil switch hole in the bock to take a larger fitting but only want to do that as a last resort as the engine is pretty much built and I don't want to risk getting metal swarf inside the gallery when drilling and tapping it out!

Advice please.

Thank you

Lee

The Dan Grand Master

The Dan

Posted
Posted

The oil pressure sensor gallery is adequate to feed the turbo with enough oil. Just get the biggest ID size you can in there. The turbo (depending on type) should have the restrictor built in or at least run a restrictor smaller than 1/8th anyway...common restrictor sizing for ball bearing is 0.8-1.0mm and for journal bearing around 1.5-2.0mm...so both are much smaller than that feed line.

leeroy_25 Community Regular

leeroy_25

Posted
  • Author
Posted

Hey man, Must picked thsi reply up! Thanks for the info.. I have a journal bearing turbo by the way.. I'll try and bore out the centre of the tee piece a bit to open it up some in that case and it should be sweet.

Cheers

Lee

The Dan Grand Master

The Dan

Posted
Posted

With journal bearing turbos you have to be careful. They are the leas likely to have a restrictor in place. I would just get a normal fitting, hook it all up and measure the oil flow from the drain pipe at idle. You should see about 1 - 1.5L/min. You will be wasting your time opening up the fitting hole if you just have to put another restrictor in there anyway.

The restrictor is best placed nearest the turbo also.

leeroy_25 Community Regular

leeroy_25

Posted
  • Author
Posted

Thanks for the reply again.. It's a Holset turbo if that helps?

I looked inside the tubro where the oil fitting goes and there are two smalle holes about 2-3m diameter.. presumably one going to each end of the turbo? Does that sound reasonable?

It would be ideal to have this sorted before I put it in the car as there won't be much room for work once it's in!

If I don't need to open out the hole in te block it would be better.. But then at the same point if I am not going to get enough flow from the smaller hole I really need to know so I can open something up.. or are you fairly confident the 1/8" oil pressure hole is an adequate feed size as it is?

Thank you

Lee

The Dan Grand Master

The Dan

Posted
Posted

You don't have many options I'm afraid.

What is the part number of the Holset turbo you have. I will let you know if there is a restrictor built in or if you need to run one and what the oil return flow should be. It's up to you to do the rest. There is no easy way to set this stuff up. All you can do is use the information you are given and make the best with what you have. Fit the turbo, run the oil line, test the flow amount from the return at idle and if it needs a restrictor, then put one in...it's simple to do. If it flows enough then leave it be.

Job done.

Get me the part number or serial number on the turbo and I'll give you the information you need.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...