Jump to content
SAU Community

Rx7 Injectors In An Rb20

Sciclone

By Sciclone,
in Engines & Forced Induction

 Share

Recommended Posts

Sciclone Enthusiast

Sciclone

Posted
Posted

Hi all,

I've read that you can fit series 5 RX7 injectors into an RB20 without too much problems, but I'm just wondering about the ins and outs of doing so. They are a high impedance injector, so it shouldn't require any ballast resistors, and they are a Top Feed, so no fuel rail mods (from what I can gather)

Has anyone done this mod and know any tricks/problems?

Link to comment
https://www.sau.com.au/forums/topic/272548-rx7-injectors-in-an-rb20/
Share on other sites
Sciclone Enthusiast

Sciclone

Posted
  • Author
Posted

Thanks for the reply Adriano.

I was specifically wondering about the electrical side of things. What type connectors do the RB20's have (oval, square, custom)? I don't have an RB20 so I can't check.

I just want to know what is involved in fitting them, as I don't want to tell some poor sod that they'll fit straight in when there could be a lot of fiddling around involved. You do that, and it'll come back on you eventually...

Rekin Grand Master

Rekin

Posted
Posted
Thanks for the reply Adriano.

I was specifically wondering about the electrical side of things. What type connectors do the RB20's have (oval, square, custom)? I don't have an RB20 so I can't check.

I just want to know what is involved in fitting them, as I don't want to tell some poor sod that they'll fit straight in when there could be a lot of fiddling around involved. You do that, and it'll come back on you eventually...

Need generic injector connectors, rb20 connectors dont fit on gtr injectors unless you cut some of the notches off the injectors.

Have to wire in GTR resistor ballast, refer to the link below for my explanation.

http://www.skylinesaustralia.com/forums/Gt...mp;hl=injectors

Sciclone Enthusiast

Sciclone

Posted
  • Author
Posted
Need generic injector connectors, rb20 connectors dont fit on gtr injectors unless you cut some of the notches off the injectors.

Have to wire in GTR resistor ballast, refer to the link below for my explanation.

http://www.skylinesaustralia.com/forums/Gt...mp;hl=injectors

I'm not worried about GTR injectors (I already have a GTR).. As the title says, its 550cc RX7 injectors into an RB20 that I'm worried about.

grandmasterb Grand Master

grandmasterb

Posted
Posted

Steve,

rx7 550's are a direct drop in replacement for stock RB20 injectors. If there going to the trouble of putting them in i would be replacing the plugs anyway for peace of mind given there age. Other than that nothing else is required.

As for spray pattern, i never had any drama's when running mine :)

James_03 Mentor

James_03

Posted
Posted

Yes they are all high impedance Hitachi injectors. Mazda changed the injector plugs to an oval style plug for the S5 rx-7. The S4 rx7 injectors should be a straight drop in.

Be aware that the NA and Turbo injectors are similar in colouring. N/A is 460cc turbo is 550cc.

N/A part number: 195500-2020 (Purple/Red top)

Turbo part number: 195500-2010 (Red top)

If you end up getting S5 550's then you can get the oval style plugs of most toyota camry's, I got a set of a V6 2001 model camry that looked almost new. Be aware but that the spray pattern is like a garden hose, and for this reason I would not recommend them. Been there done that.

Personally I would be to go for Sard's or Nismo even if it does take a little longer to save for them.

Sciclone Enthusiast

Sciclone

Posted
  • Author
Posted

Thanks peoples. As I said, I have a GTR, so they're no good for me. I just don't want to rip someone off like I was.

Btw James, I think you have the part numbers the wrong way around. Every rx7 forum I've been on has the 2020's as the 550cc turbo injectors.

Sciclone Enthusiast

Sciclone

Posted
  • Author
Posted

Femno's got it in one...

I was ripped off as the person who sold these to me said they were a straight swap in for a GTR.... Now I have to find some way to recoup some my losses ie. sell them, without doing the same thing to someone else.

Ideally, I'd just like to give them back to the dude that sold me them and get my money back, but that's as likely as a hole in the head. So if anyone knows of any drag/drift cops with RB20's that want bigger injectors....

Sciclone Enthusiast

Sciclone

Posted
  • Author
Posted
Femno's got it in one...

I was ripped off as the person who sold these to me said they were a straight swap in for a GTR.... Now I have to find some way to recoup some my losses ie. sell them, without doing the same thing to someone else.

Ideally, I'd just like to give them back to the dude that sold me them and get my money back, but that's as likely as a hole in the head. So if anyone knows of any drag/drift cops with RB20's that want bigger injectors....

Don't worry all.. they do fit my RB26 after all, albeit with some modification to the loom...

Looks like I'll have to scour the wreckers or something...

Note to self: Check part numbers etc before buying..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...