Jump to content
SAU Community

Recommended Posts

hey, i was just driving to band practise this afternoon and my skyline started jerking under acceleration (felt like it wasnt getting enough petrol even though my foot was pushed down).

So after this i babied it home, it than started doing the same thing just at 60kms at around 3000rpmish.

I pulled over checked the engine bay and everything wasn't leaking (aside for a bit of caked oil around the turbo manifold)

I had to pull over again and let it idle, this time it actually died, so i started it again and it started find kept its idle fine.

So i continued to drive home and it would do the same thing where it would jerk (felt like the engine was being starved of fuel) at 60ish.

So I'm new to skylines but i'm fairly sure this is a fuel pump issue. Though about a month ago i came home and the car wouldnt idle one day after a bit of a drive and idle really radically going

from 500rpm almost stalling and back up to 2000rpm ect. only lasted about 10 seconds though.

Would this be my injectors? (pretty sure its still the stocko injectors) and is there a way i can test them at home? Could a dodgy spark plug lead or spark plug do this???

I've just had a major service done last week (belts,pulleys,thermistor,waterpump,timing belt) So i'm pretty sure its definitely the fuel system.

thanks in advance hamish

Link to comment
https://www.sau.com.au/forums/topic/273209-skyline-losing-power/
Share on other sites

was it doing this?

afm prob

if so its prob your afm mate

not really like it would drive completely fine for one miniute reving all the way. than the next you'd put your foot down and the revs would just continue to drop than cut back in for a split second and drop. and than it would kick back in and drive normally for a bit longer (happened around 3-4000rpm) could be the AFM though, I'm going to replace the fuel pump and check the AFM.

ALso if it is the AFM what am sposed to do? just replace the air/fuel mixture sensor unit? are they expensive? or can i open it up and check out the joints (i'm a 4th year apprentice electrician)

not really like it would drive completely fine for one miniute reving all the way. than the next you'd put your foot down and the revs would just continue to drop than cut back in for a split second and drop. and than it would kick back in and drive normally for a bit longer (happened around 3-4000rpm) could be the AFM though, I'm going to replace the fuel pump and check the AFM.

ALso if it is the AFM what am sposed to do? just replace the air/fuel mixture sensor unit? are they expensive? or can i open it up and check out the joints (i'm a 4th year apprentice electrician)

both the joints were fine on my gtr

but have ago if you want

there pretty cheap on here

i paid 150 for a pair on here

both the joints were fine on my gtr

but have ago if you want

there pretty cheap on here

i paid 150 for a pair on here

checked the fuel filter, changed it (it was clogged up to shit house), cleaned and sprayed the AFM and pod filter. Added some "nitrous" brand in tank fuel injection cleaner.

turned the car over still doing it

revs between 2500 - upwards misses or something just drops out of rev for a split second tries to catch up to where you were revving it than cuts out again and so forth.

changed spark plugs with iridium expensive ass ones (original spark plugs were f**ked), and brought new super spark coil packs.

turned over still doing it!?!?!?

Is there anything else that could be the problem i'm running out of money and need to get the car going.

had another look under it and noticed a little bit of oil from the turbo (could this be a turbo related problem)

or do i need to buy a new AFM?

should i just take it to a mechanics? (will be expensive as i will have to tow it back and forth)

if anyone knows of any good skyline mechanics or friends in logan help would be greatly appreciated!

Hey mate my mates car was doing this when he first bought it. after alot of stuffing around it turned out to be someones dodgy wiring off the ecu. 1 wire was hanging doing nothing and every time it touched something it stuffed the car up. check wiring otherwise sounds like it could be the fuel pump dropping volts. not uncommon. i suggest you get a multi meter onto fuel pump and some fuses and check everything. good luck

Oh thank god...

I just picked up my R33 Series 3 GTR about 5 days ago and she does this at least once every few days. Had no issues yesterday but driving home from work today, she died on me twice as the power just drained...ks dropped off, boost gauge needle went nuts, revs dropped to well below 1000 and then just died altogether. i was able to keep it alive for most of the drive by keeping the foot down and revving higher than i usually would, but this didnt always work. Luckily its under warranty for the time being...but i live about 90 mins from where i bought the car. so...this is a pain. do we have a definite cause - the afm or fuel pump - or is it a random thing?

checked the fuel filter, changed it (it was clogged up to shit house), cleaned and sprayed the AFM and pod filter. Added some "nitrous" brand in tank fuel injection cleaner.

turned the car over still doing it

revs between 2500 - upwards misses or something just drops out of rev for a split second tries to catch up to where you were revving it than cuts out again and so forth.

changed spark plugs with iridium expensive ass ones (original spark plugs were f**ked), and brought new super spark coil packs.

turned over still doing it!?!?!?

Is there anything else that could be the problem i'm running out of money and need to get the car going.

had another look under it and noticed a little bit of oil from the turbo (could this be a turbo related problem)

or do i need to buy a new AFM?

should i just take it to a mechanics? (will be expensive as i will have to tow it back and forth)

if anyone knows of any good skyline mechanics or friends in logan help would be greatly appreciated!

Ok, so, I just had my GT-R fixed, which was having many of the same symptoms as yours.

AFM problem. Only, not your traditional sort of AFM problem. The vacuum hose connected to the AFM on my GT-R had become disconnected and so the AFM was receiving faulty readings and causing the car running problems. The boys at the dealer hooked the hose back up, switched out my AFM just in case it was also contributing to the problem and sent me on my way. Hasn't missed a beat since. Might be something to look at. Failing that, get the car up on a dyno...the computer should be able to tell you whats gone wrong and where.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...