Jump to content
SAU Community

Recommended Posts

Noticed a bit of a problem with my car last night, and its been doing it a bit this morning. Basically with a constant very low throttle applied, the car appears a little stuttery...not massively, but i can feel something.

Its a bit hard to explain, but its basically feeling a little lumpy and not otherwise as smooth as it should be around 2500rpm and 5-10% THR (on my S-AFC) just cruising around at 60km/hr or so. On heavier acceleration its fine, at idle its pretty much fine, and if i foot to the floor it, it goes at its usual rocket pace with no problems. Its almost the is like a "gurgle" or choke in the exhaust - the sort of thing you get before a backfire.

So any suggestions?

Could it be timing?

Could it be a vacuum leak (doubt it, checked all that, building up boost fine)

Could it be S-AFC settings running to rich or something? (hasn't been tuned since my new 910 fuel pump)

Could it be spark plugs? although these were only changed around 5-8k ago

Could it be something like my accelerator cable? I do notice there is a bit of slack on it. Is that normal?

Link to comment
https://www.sau.com.au/forums/topic/27375-problem-on-light-throttle/
Share on other sites

my first guess would be that ur safc might be tuned a little rich on lower rpms

mine was like that, was a little sluggish and felt like it wanted to go but couldnt till i hit boost

a tune fixed it right up, also fixed up the loss of pressure between gears somehow

try that first then go from there

remember ur car hasnt been tuned in a while and should be retuned every 2-3 months if it only has a safc

S-AFC helps a lot of things ;) although it will be less useful on a GTS, it may help it run a little smoother.

Think it could have been a bit of dodgy fuel (Caltex Gold out country way.. is that only 94RON ? ), seems to be running a lot better today, and i've still only got fairly low octane stuff in there. Its tuned for 98RON and hard use, probably a good idea to get it back on the dyno like Kami was saying and get it retuned.

I also tightened/checked all the vacuum points, so it may have been that too.

I too get some splutter low down, under medium throttle. Im putting it down to my SAFC settings. It was only ever tuned on full throttle. So when i get some time (very soon) im hiring a dyno for an hour, ($50) and going to try and squeeze a little more out of her plus do some lighter throttle testings.

You raise an interesting point. That is the big problem with dyno tuning I think. A lot of it is just done to get the highest peak power reading, which isn't necessarily good for daily driving (or in fact most driving, even on the strip or track). Some tuners are more realistic and realise you're not going to be running at full boost all the time, and tune for more across the range.

I am a believer that dyno tuning is useful to sort some things out, but it also needs a good road tune as well to tidy things up. After all, you drive on the road, not a dyno!

I asked about the low throttle settings and they said nah they are ok. I noticed at light throttle the A/F ratio was 14.2 whilst on the dyno. To me this is still rich. I think 14.7 is optimum on light throttle.

Anyway, i will throw it on a dyno and do the changes myself, may pick up some economy too.;)

guys i *always* get mine tuned on the road as it is just more realistic

also i get mine tuned on bout 1/3 - 1/2 throttle

it boosts up so much better - and i still get full boost

there is no need for full throttle imho

btw gordo if u want it retuned for the street it will cost ya bout $20 ;)

but melb is about 9% difference in the way that the environment is compared to here

still a tune up here should be good for down there too :)

Originally posted by predator666

Noticed a bit of a problem with my car last night, and its been doing it a bit this morning. Basically with a constant very low throttle applied, the car appears a little stuttery...not massively, but i can feel something.

Its a bit hard to explain, but its basically feeling a little lumpy and not otherwise as smooth as it should be around 2500rpm and 5-10% THR (on my S-AFC) just cruising around at 60km/hr or so. On heavier acceleration its fine, at idle its pretty much fine, and if i foot to the floor it, it goes at its usual rocket pace with no problems. Its almost the is like a "gurgle" or choke in the exhaust - the sort of thing you get before a backfire.  

So any suggestions?  

Could it be timing?

Could it be a vacuum leak (doubt it, checked all that, building up boost fine)

Could it be S-AFC settings running to rich or something? (hasn't been tuned since my new 910 fuel pump)

Could it be spark plugs? although these were only changed around 5-8k ago

Could it be something like my accelerator cable? I do notice there is a bit of slack on it. Is that normal?

Well there,I have exactly the same problem and my mechanic thinks I am wierd. I just had my standard fuel pump replaced with a 800 horsepower bosch unit, and its doing what yours does. More so when its cold. They put the car on dyno when warm and they said all the mixtures are fine etc. New plugs, cleaned injectors, cleaned fuel lines, new fuel filter, cleaned fuel rail, cant be the fuel system. I am taking it in wednesday night, returning thursday morning and taking them for a drive to show them so they dont think I'm mad. Some others here have advised they check the throttle position etc and see if that helps.

I'll let you know how it goes.

Paul

Dont bother setting any low throttle mapping on the SAFC. The ECU simply relearns around it to maintain the stoich AFRs. Trust me i've tried... You can even wind in 30% richer at a cruising rpm and within 10 seconds its back to stoich AFR by looking at the o2 output...

I reckon you should get your injectors etc checked out first. Just leave the low thr map empty.

The ECU runs closed loop all the time, except for when you got your foot flat to the floor above ~3000rpm. Its constantly recorrecting its sensor parameters to stay at stoich AFR so by trying to fool it with the SAFC inside of closed loop operation is futile.

You shouldnt need an aftermarket comp to fix these problems. Its most likely a vacuum leak, very dirty throttle body, clogged PVC, leaky pipes, malfunctioning EGR/Canister control, plugs etc etc. The list could go on. I suggest you get ur hands on a workshop manual and try and diagnose a few things...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GCG is a good company, they're a major distributor for Garrett in Japan as well.
    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
×
×
  • Create New...