Jump to content
SAU Community

Recommended Posts

Hey Guys, have got a few things for sale, will keep adding to the list as i find more stuff

All this stuff to suit RB26DETT, all brand new

ARP Main Studs $225 inc Freight

ARP rod Bolts $75 inc freight

ACL Race Series Main bearings Std Size $110 inc Freight

ACL race series Conrod bearings Std Size $55 inc freight

R33 GTR Crank, brand new $900 plus Freight

All this stuff still in boxes

More stuff

RB26DETT Block with main girdle/cradle: Has been hot tank cleaned, bored out to 87mm, decked a fraction to tidy up the face of the block. has had the mains girdle/cradle fitted and checked the tunnels for out of round/out of spec(Needs welch plugs fitted). $1000 plus freight

Venolia 87mm forged pistons to suit RB26DETT, Brand new in box, with Nissan Genuine rings ready for fitting. All ciclips/gudgen pins etc there as well. $1100 inc freight

STD AFMx3 $20 each

R32 GTR Crank Angle Sensor $50

6x Coil packs $70

ABS Module $120

R32 GTR Steering Rack with tie rod ends $150

R32 GTR Clutch slave Cylinder $40

Clutch Master Cylinder $50

Brake Booster and Slave cylinder $150

A/C condensor $50

STD R32 GTR BOV $130

A/C Fan(Fan that sits in front of condensor that also switches on when engine gets too hot) $50

R32 GTR Bonnet Catch $80

Front wheel speed sensors $50 each

Rear Seat(No rips, bit dirty and faded though) $50

Passenger Seat(No Rips) $150

LH Door(White and complete) $250

Bare steering column $40

Glovebox Lid $10

Tailights(White Surrounds) $60 each or $100 pair

STD Fuel Pump $100

Drivers Side Headlight $100

Front propellor shaft $50

Starter Motor $50

Another 6 coil packs $70

Coil pack resistor $40

Rear window $50

Quarter windows $60 each or $100 pair

Front Crossmember $100

Tailshaft $80

ALL PRICES ARE EXCLUDING FREIGHT

Michael for questions 0438911374

Thanks

Link to comment
https://www.sau.com.au/forums/topic/274508-rb26-and-r32-gtr-stuff-for-sale/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...