Jump to content
SAU Community

Recommended Posts

i've been thinking about these

my insurance company and they say that any modification is cool as long as its legal.

are power fc's and electronic boost controllers considered legal?

if they're not what do the rest of you do, as i could live with the fact of having them stolen and not have them covered (only just)but if i have a serious crash and the assessor see's them would they refuse to pay?

thanks peeps

James

Link to comment
https://www.sau.com.au/forums/topic/27482-insurance-settle/
Share on other sites

james, the way i see it is this:

the only people who are interested in the legality(?) of your modifications are the RTA. When they become "illegal" is when you start filling your car up with cocaine or start installing machine guns as anti-car-jacking mecahnisms. the police are the ones who try and keep the roads safe from unroadworthy vehicles and thus you get defect notices.

so if your interested in whats legal, or what should be more appropriately termed "road worthy", you should start at the RTA website. from there you'll find a plethora of pdf files which basically say, any modification to your vehicle should be checked by an RTA authorised workshop who can then give you an engineer's certificate deeming it as "roadworthy" and thus free from defect notices (in theory).

in your case, an ecu is indirectly associated with your intake system so i would say it would need to be engineered as it has rather large bearing on your fuel mixtures and hence emissions.

Link to comment
https://www.sau.com.au/forums/topic/27482-insurance-settle/#findComment-577016
Share on other sites

no.. its not the engineers job to report people, nor is it the EPA's job to report people - generally a cop takes it upon themselves to do this with only a rough understanding of the rules as set out by the RTA or EPA, etc. Often they're wrong, often they're not :) You are probably best asking in the Sydney area actually specific questions - as the rules and enforcement tend to vary a lot between state and state.

Basically any device that alters the emissions is considered illegal, so that would include a PowerFC and boost controller. But depending on who you are pulled over by, and who inspects your car the definitions seem to vary.

THe problem is there is no definitive "list" of what is legal and not legal by any of the main traffic authorities, and there damn well should be to properly clear things up once and for all. Often you have to wade through pages of obscure ADR's to find what you're looking for, and even then not everything is properly explained with relevence to common items out there in today's cars.

Link to comment
https://www.sau.com.au/forums/topic/27482-insurance-settle/#findComment-577513
Share on other sites

so in your case, a powerfc looks just like a stock ecu. so there's a fairly minimal chance a plod could tell you have an aftermarket ecu from looking either in your engine bay or interior. that said, i doubt they'd know what a bleed valve looked like also.

i've heard one story where an insurance company went to the extent of contracting a mechanic to inspect a vehicle for mods that would voided his insurance claim. sure enough, the ecu was found to be aftermarket and the claim was void.

moral of the story, tell the whole truth or prepare for the worst circumstances...

Link to comment
https://www.sau.com.au/forums/topic/27482-insurance-settle/#findComment-578095
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...