Jump to content
SAU Community

R34gtt Aftermarket Delights..

Tom Monk
 Share

Recommended Posts

Tom Monk Explorer

Tom Monk

Posted
Posted

sadly i had to remove these parts from my 4door shes in trouble with the law and i gotta stock her out..All these parts came from running car so no junk!

-Apexi PowerFC with hand controller $1,250.00

-BLITZ 525cc injectors (will only suit NEO 25motors) $650.00

-Z32 Airflow meter with Tomei plug $300.00

-NISMO 1.5 way mech LSD 4:1 Ratio direct fit ER34 $900.00

-Silk Road rear camber arms as new condition suit 33,34 and S14 $250.00

-TEIN Castor rods suit ER34 & R32GTR good condition $220.00

-KTS Hicas lock bar $200.00

-BRIDE super low RH seat rail suit BRIX recliners etc $200.00

-SAFETY 21 6point bolt in rollcage direct fit R34 4door (rear hoop and legs is compatible with R33) $650.00

Thats all for now will post pics up next couple of days,

can ship interstate if need be.

located in Modbury North SA

cheers,

Tom

Link to comment
https://www.sau.com.au/forums/topic/275973-r34gtt-aftermarket-delights/
Share on other sites
Tom Monk Explorer

Tom Monk

Posted
  • Author
Posted

BRIDE rail will only suit bride recliners(bottom mount) and possibly RECARO recliners also bottom mount definitely not standard seats...

i was running a HKS 2835 ProS with the injectors FC etc to make a solid 270kw @ 16psi and with a bigger turbo could have easily made more with the current injectors..

They were bought brand new from JMS only recently and i ran the car at the first round of the SA G1 drift championship and it was bulletproof..not bad for a daily driven set up..

post-57991-1245769321_thumb.jpg

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...