Jump to content
SAU Community

Recommended Posts

I have 235/40ZR18s on front and 265/35ZR18s on back... ...now one friend is telling me they should be 28psi front and 30psi back... ...where another is saying 38psi and 40psi... ... The last few time I've checked them I've kept all four at 34psi... ...(the new auto air pumps are great for that)...

I'm sick of hearing these two go on and on about what is right... ...so does anyone else know what the should be???...

Link to comment
https://www.sau.com.au/forums/topic/276009-quick-pressure-question/
Share on other sites

Yes the eternal mystery! I know on the track you should set the presures quite high (around 40psi) but on the street (and in the wet) thats a bit much I believe. Especially if you have super hard suspension. Remember the tyres do need to move a bit to absorb bumps etc.

nooo. on the track generally you will be lowering from your street pressure as they will rise with the added loads of track driving.

it's really down to the type of tyre, type of use, manufactures recommendation and personal preference as to what is best on the street.

as a general rule the more pressure you put in the 'sharper' it will feel handling wise. it will feel like it turns better and it will transmit more bumps etc to the cabin. over a certain point though traction will be reduced as the reduced compliance in the tyre means it will loose traction more easily.

less pressure will give you a little more roll and give a nicer ride with less bumps etc transmitted to the cabin. too low though and it will damage tyres sidewalls and will give poor handling and traction,

the trick is to find the sweet spot. I would start at around 30-35psi all round for street driving for most regular radial street tyres. adjust a little up or down within that range and see what you prefer. keep and eye on the wear too.

As you increase the pressure, you will increase the overall stiffness of the tyre, which will contribute to the ability of the tyre to get you around a corner. But, you will also decrease the contact patch area of the tyre. There comes a point where the added stiffness is overcome by the reduced contact patch, and the car no longer likes to go around corners.

If anything, you need higher pressures in the front tyres - this will have the effect of reducing any understeer. For your setup, I would recommend 38 front, 36 rear for general road use. But maybe check what the manufacturer recommends, and then basically ignore it. Add at least 2psi to what the manufacturer recommends, making sure you still have more pressure in the fronts.

In the wet, ADD pressure (about 2psi or so) - what this does is hold the tread in a more open configuration, allowing the tyre to more easily pump the water from beneath the tread.

Thanks guys...

I guess I'll stick with what I've been doing and leave it at 34psi all round... ...Maybe pump the front up a little... ...Both mates agreed that the rear should have a little more in them because they are a wider tyre... ...But you all recommend less in the rear...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...