Jump to content
SAU Community

Recommended Posts

gday all,

i have here for sale a complete Greddy T67-25G turbo kit which came off the car which i bought not that long ago which had an RB24 in it.

the RB24 was removed from the car prior to my purchase and the turbo kit is way too big for the standard RB20DET which currently runs in my car, so i have no need for it.

the turbo kit itself is in excellent condition and the turbo has no play whatsoever and spins freely.

the manifold has 2 hairline cracks, but they will be fixed before being sold.

the kit consists of the following;

* Greddy T67-25G turbo with 8cm turbine housing

* Greddy high mount tubular manifold

* Greddy Type R external wastegate with 10psi spring

* 3.5" turbo/dump pipe to cat

* intake pipe

* Z32 afm to suit

this kit would be ideal for anyone that wants to build a very tough and streetable 300+ rwkw street/circuit RB25 or RB24det.

Price: $3600.

will post pics very soon.

* turbo kit is in melbourne. PM me if you are interested.

Edited by RS500
Link to comment
https://www.sau.com.au/forums/topic/277175-rb20rb25-greddy-t67-25g-turbo-kit/
Share on other sites

would be interested in pics of the kit, as well as pics on the car. what kind of power was it making, and when did it hit full boost. cheers

hi there,

below are some pics from when the turbo kit was on the car before i purchased it.

T67_engine_1

T67_engine_2

T67_engine_3

as for power & boost, it never got it tuned to see the full potential as it was only running a chipped r32 ECU, but with the RB24 it felt quite responsive and power delivery was quite linear. It also moved for only 10psi ;-)

i'll get some more pics of each item over the weekend.

fyi, this turbo is a perfect match for the RB25 or RB30DET.

would this be a laggy turbo on a rb25det neo? what rev range did you hit full boost (and what psi) just so i have a rough idea.

would this be a laggy turbo on a rb25det neo? what rev range did you hit full boost (and what psi) just so i have a rough idea.

hi there,

it depends on what you would define as laggy?

if you're looking for the same response as the factory turbo, then this would be laggy for you.

re: full-boost, etc, like i wrote previously, this setup was on the car when it had an RB24DET (stroked RB20) before i bought it so i'm not sure when full boost came in exactly b/c i didn't get to drive it.

although, i was taken for a drive as a passenger and with the RB24, it didn't feel laggy, and it was only on 10psi.

fyi, the RB25DET NEO is a good flowing engine and it will run this turbo perfectly.

also to add, for the guys who might be considering this setup for their RB20/21/22/23 or RB24, i also have available the following for an extra $400.

* an RB20DET inlet manifold with 550cc/min injectors & adjustable fuel reg

* and chipped r32 ECU to suit this turbo kit

thank you.

Edited by RS500

gday dudes, i've had some queries but no follow-ups.

for anyone interested, i'm willing to let the kit go for $3300.

again, the kit is in Excellent condition, the turbo is perfect, no shaft movement at all.

what u rekon this would b like on a rb22 with poncams?

I really think this would work well with your rb22 & poncams.

the extra capacity and flow from the cams will help this turbo work a treat on your engine for both street & strip/circuit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...