Jump to content
SAU Community

Recommended Posts

search for 'shitty r34 interior' or something like that, there is a large thread covering this.

- pull out the ashtray and remove the screw behind it

- remove gear knob by unscrewing it

- pull up the gear stick surround, (there are small clips holding it, just pull gently upward

- remove the wire harnesses going into the back of the cig lighter.

- wrap a flat screw driver with a thin cloth and pry out the a/c vents from either side of the centre console surrounds (dont be scared this part is simpler than it sounds)

- undo the 2 screws that were behind the gear stick surround near the ashtray/ cig lighter

- undo the 2 screws you revealed from removing the a/c vents

you now have access to the cage holding the a/c unit and headunit

4 screws hold the remaining piece of fascia around the a/c unit and headunit that can be unscrewed from behind the cage

If you have a triple gauge cluster, there are 2 screws that hold that in from the front, which were also revealed when removing the a/c vents, unscrew these and the unclip the wiring harnesses and you can now take off the cluster.

to access the plastics around the window controls on either door you need to remove both door skins by unscrewing all of the screws holding it in and the pulling on them gently to pop out the clips holding the skins on from the inside.

don't pull too hard as you then need to lift the door skin upward to get the top section out from where the window slides down.

Finally you unclip the wiring harnesses running behind the door skin to the window controls on the door skin.

You can then take the door skin completely off and unscrew and screws and pop out the small clips holding on the plastic surrounds, take your time to make sure you don't snap any.

After all that, have fun spraying, and do all of this in reverse order to refit.

search for 'shitty r34 interior' or something like that, there is a large thread covering this.

- pull out the ashtray and remove the screw behind it

- remove gear knob by unscrewing it

- pull up the gear stick surround, (there are small clips holding it, just pull gently upward

- remove the wire harnesses going into the back of the cig lighter.

- wrap a flat screw driver with a thin cloth and pry out the a/c vents from either side of the centre console surrounds (dont be scared this part is simpler than it sounds)

- undo the 2 screws that were behind the gear stick surround near the ashtray/ cig lighter

- undo the 2 screws you revealed from removing the a/c vents

you now have access to the cage holding the a/c unit and headunit

4 screws hold the remaining piece of fascia around the a/c unit and headunit that can be unscrewed from behind the cage

If you have a triple gauge cluster, there are 2 screws that hold that in from the front, which were also revealed when removing the a/c vents, unscrew these and the unclip the wiring harnesses and you can now take off the cluster.

to access the plastics around the window controls on either door you need to remove both door skins by unscrewing all of the screws holding it in and the pulling on them gently to pop out the clips holding the skins on from the inside.

don't pull too hard as you then need to lift the door skin upward to get the top section out from where the window slides down.

Finally you unclip the wiring harnesses running behind the door skin to the window controls on the door skin.

You can then take the door skin completely off and unscrew and screws and pop out the small clips holding on the plastic surrounds, take your time to make sure you don't snap any.

After all that, have fun spraying, and do all of this in reverse order to refit.

that seems to technicall for me lol

do you rekon i could just get some paint and go round the areas or you think that will result in a shitty turnout ?

Honestly bud,

It would look terrible if you were to just paint over it, not to mention do you really want to use spray paint inside your car?

It's not at all technical, it just sounds like it, but really, it should take you no more than 5-10mins at the very most to remove all of the centre console section, the doors are a little bit trickier and require a bit of fiddling around, but i think its worth it.

But i definatly would not recommend spraying the parts without pulling them out and just scouring them with some metho (again, that is also very simple to do)

that seems to technicall for me lol

do you rekon i could just get some paint and go round the areas or you think that will result in a shitty turnout ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...