Jump to content
SAU Community

R34 Gtt Triptronic

Akis
 Share

Recommended Posts

Akis Collaborator

Akis

Posted
Posted (edited)

Hi,

I have a R34 GTT with the triptronic, i bought a Power FC, i installed it, started up, did the idle learn

and went for a ride...

The car stays at some gear(3rd i think) and that's it, no triptronic and not good mixture...

What can i do about this? Except manual conversion...

Akis

Edited by Akis
Link to comment
https://www.sau.com.au/forums/topic/279503-r34-gtt-triptronic/
Share on other sites
skylinecouple Experienced

skylinecouple

Posted
Posted

It's a shame you didn't do some research before you bought it. Haven't seen you on the forums before so I'll assume you didn't know what almost everybody else does, PFC is for manual only. You need to contact Toshi, do a search.

666DAN Grand Master

666DAN

Posted
Posted
I did searched it... but i saw that the only thing that it could be a problem where the harsh gear changes..

Today i bought a manual conversion so i guess everything wil be solved.. :D

Thanks for answering..

Akis.

Harsh..more like *no* gearchanges ;) When you take out the ECU, you remove the control unit for the transmission, that's why it stays in 3rd. If you had a 25GT, it would have run just fine though, bloody Nissan.

A conversion will sort that out though ;)

iseekool Veteran

iseekool

Posted
Posted
Harsh..more like *no* gearchanges :) When you take out the ECU, you remove the control unit for the transmission, that's why it stays in 3rd. If you had a 25GT, it would have run just fine though, bloody Nissan.

A conversion will sort that out though :)

Is the auto trans control on a non-turbo R34 separate?

iseekool Veteran

iseekool

Posted
Posted
Yep, it's only the GTt that has the intergrated TCM.ECM the N/A has the TCM seperated, so when you take out the ECU it still has gearshift capability.

So how I "understand" it the non-turbo auto would be better suited to aftermarket ECUs - if that's what you intend on doing...

  • 2 weeks later...
  • 3 months later...
Klymax Contributor

Klymax

Posted
Posted
It is absolutely Plug&Play. :(

Hi Akis,

I know the thread is a little old but hopefully you may know an answer, I know of some series 1 98 skylines that have had a manual conversion using the auto loom are having problems with the plug and play PowerFC. infact its not as plug and play as we thought, problems with the TCS, Engine light and Aircon compressor. Any idea's why we'd be having such issues?

Cheers

Akis Collaborator

Akis

Posted
  • Author
Posted

TCS and engine lighl and also Slip are on because the Power FC doesn't co-operate with the TCS so check engine is on. That's what happened with mine. I do not need the TCS.. i think it is better to have the control by yourself.. ;)

About the aircon compressor i havent noticed anything..

For the engine light i think there is a solution..

  • 7 months later...
  • 2 weeks later...
splice Newbie

splice

Posted
Posted

hi akis i would appreciate any help you can give, am desperate. looking for the part # for an r34 rb25de neo

transmission ecu and also if i can get a picture of the connector to that ecu, thanks in advance.

Augustin.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...