Jump to content
SAU Community

Recommended Posts

got some series 1 r33 skyrine parts for sale.

r33 radiator. 150

cat back exhaust, 3inch to dual 2.5. 300

left front gaurd. 50

boot and spoiler. 150

left door, no trim. 100

33 tailshaft, 200

centre consol. 50

airflow metre. 50

glove box. 50

rear trim bits, were the two rear doors would be. 50

front lights, ones got a fair good smash but still usabl. 50

rear lights, one has a crack. 100

rear seats. 100

rear bar. 150

front bar. 150

wash bottel with lines. 20

over flo bottel. 20

RB25 intercooler piping. 100

air condition core. 100

in adelaide.

0411592938

Link to comment
https://www.sau.com.au/forums/topic/280060-r33-skyline-parts/
Share on other sites

Hey mate... Just a few questions, what colour was the car? and can you upload pics? cheers

:thumbsup::thanks:

lol

car is white.

100_3256-1-1.jpg

100_3257-1.jpg

100_3258-1.jpg

skyrine-1.jpg

also got some stock 33 springs to. 100 buks

Edited by scottmiller92
  • 2 weeks later...
got some series 1 r33 skyrine parts for sale.

r33 radiator. 150

cat back exhaust, 3inch to dual 2.5. 300

left front gaurd. 50

boot and spoiler. 150

left door, no trim. 100

33 tailshaft, 200

centre consol. 50

airflow metre. 50

glove box. 50

rear trim bits, were the two rear doors would be. 50

front lights, ones got a fair good smash but still usabl. 50

rear lights, one has a crack. 100

rear seats. 100

rear bar. 150

front bar. 150

wash bottel with lines. 20

over flo bottel. 20

RB25 intercooler piping. 100

air condition core. 100

in adelaide.

0411592938

do u post to melbourne??? i need a wash bottel, is it the same as the one in a R33 S2???

thanks!!!

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...