Jump to content
SAU Community

Recommended Posts

Hi,

I have a set of rims with tyres for sale.

Rims are Impul RS, they're 17x8 on all four, 3 piece wheels with polished rims, rears have some dish in them, front offset is +38 and rear offset is +32, one of the front ones have a slight dent on the inside and it'll cost about $100 to get repaired, it doesnt leak air.

comes with tyres, rear tyres have some serious camber wear, but front Yokohama tyres still have about 30~40% thread.

asking $400, pickup only, located in kograh

also a set of factory R32 GTST radius rods, comes with polyurethane bushes in good condition, they're eccentric for caster adjustment,

asking $100, will ship these interstate at buyer's expense.

Edited by chiksluvit

hi,

these wheels will definitely fit r32 and S14/15 as well

clears R33 brake calipers fine, so they won't have issues with R32, silvia, R34 calipers

cheers

How BAD is the dent?

is it drivable?

Is it necessary to fix?

Is it noticable from the outside?

Can the rears be fitted to the front of a 33 and clear the calipers aswell?

How BAD is the dent?

is it drivable?

Is it necessary to fix?

Is it noticable from the outside?

Can the rears be fitted to the front of a 33 and clear the calipers aswell?

Its drivable, doesnt leak air, not noticable from the outside since its on the inner rim edge.

I would get them repaired though for peace of mind, dents like this cost about 100ish, ok for street driving as you won't notice during street driving 80 and below, I'll take a photo of it if I go tomorrow

The rears can't be fitted to the front, rear wheels won't clear the front calipers, due to the depth of the wheel stud holes/ thickness of the 5 spoke disc.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...