Jump to content
SAU Community

Recommended Posts

ok so seeing as my previous thread on this topic has disappeared

i'll continue on in a new one

i'm a little bit worried about snapping studs as one would be with this kind of job, even to the point of considering buying/borrowing a torque wrench so i don't snap any when i do them up

not so worried about getting them off as the head was taken off only a couple of years ago so hopefully they won't be too bad

my question, would it be worth the torque wrench idea and if so i don't suppose anyknow knows the amount of torque required for the nuts or where i could find that figure out

thanks.

Link to comment
https://www.sau.com.au/forums/topic/281354-exhaust-manifold-gasket-replacement/
Share on other sites

if u have a exhaust leak there is a good chance there is one snapped the already

some times they will snap when u r removing them

some times they wont untill u tension them

depends on how much of a hard life (heat) the eng has had imo

and mabe some luck

but get your self a good left hand drill set and easy outs

good luck

exhaust studs are fun, ive none a few where they havent broken, and just as many that have broken, spray inox, wd40 on the treads before trying to remove them.

inspect the studs before refitting the manifold. i always use a thread chaser to clean the treads before refitting. use copper grease on threads and dont over tighten.

if there is going to be one that will snap it always seems to be that last one, lol.

yeah sometimes they break, other times they don't. when i put extractors on my pulsar none broke, and when i pulled them off again to fix something a few months back (had been on there for about 4 years) none broke either. however on my 33 i had 2 break just while driving, and another 2 broke getting the manifold off. similar thing happened with a mates 33 when upgrading the turbo. 1 stud broke just putting the wrench on.

I just put the 32 into the shed to do this job + a few others as well I bought a cometic exhaust gasket from repco for around $80 and new studs n bolts for around $40. Attempting to do this job over the next week or so Its supposed to be a 4 hour job for someone who hasnt done it yet (me haha) good luck will keep yas posted

say i do break a stud,

getting new studs, just the champion packs of them from autobarn etc would do ?

Get them from Nissan, it's cheaper.

I just put the 32 into the shed to do this job + a few others as well I bought a cometic exhaust gasket from repco for around $80 and new studs n bolts for around $40. Attempting to do this job over the next week or so Its supposed to be a 4 hour job for someone who hasnt done it yet (me haha) good luck will keep yas posted

4hrs is generous.

They are ok, i can supply you with gaskets and studs, let me know and i will get you a price, its around a 3 hour job.

Lol. 3hrs until you break one. Then add at least half hour per stud.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...