Jump to content
SAU Community

Recommended Posts

While we have a thread open and I can't be f**ked searching, which is the best (not necessarily the most expensive) lock kit to get?

I got mine from "New Parts" Section on Nissansilvia ages ago. from QLD seller. was $99, had all the parts easy to install. nice strong bar. wasnt a cheap hollow feeling.

som1 would know this.. my when i pulled out my Hicas system out i realised on the inside part where the tie rods connect to the hicas bar that my stock unit was Welded together.. would this be a method of stopping hicas? all related pipes and such were already removed.

Just learn to drive properly and Hicas is your friend. Then you don't need a lock bar.

He might be doing some track work and wanting some consistency there, Hicas isn't always your friend...

That's why I want to lock the HICAS. I've heard it's fairly unpredictable at certain speeds and I'd like to be able to control my oversteer without another variable in the already large equation.

That's why I want to lock the HICAS. I've heard it's fairly unpredictable at certain speeds and I'd like to be able to control my oversteer without another variable in the already large equation.

I hear people say that all the time. I bet 95% of the people who say it have read it, but never experienced it. When Hicas does its thing, 99% of the time you don't feel it. If you're pushing hard and you do feel it, just go with the flow, it's certainly not un-predictable if you understand what it is going to do..

Why remove all that tech and development in hopes that a solid bar will do a better job, especially if has never been a problem for you. Don't remove it just because you read something on a forum somewhere, some clever little Japanese men put a lot of thought and money into designing a system that does some really clever things to improve handling and driveability. If a solid bar was better, Nissan would have installed it in the factory...

Unless you're trying to reduce the weight in the car, and you never plan to drive around corners (eg drag car), or you plan to do loads of drifting, save yourself the $$ and learn to enjoy the hicas.

Problem is, this is a computer controlled thing...and it's not constant...being dependant on speed and your angle of steering. Judging by the pic above it's just an unnecessary variable thrown into the equation. I don't want to get used to controlling it, as for the most part of track driving I can only see it being detrimental. I can appreciate the technology that went into it, but just like traction control and ESC, no thanks.

See I actually liked Honda's four wheel steer (atleast the one in the 2nd Gen preludes). It only operated at low speed so it made the things a dream to park (had to be careful of front wheel drive oversteer when booting through round-a-bouts) and didn't affect handling at higher speed.

That's what I thought HICAS was going to be like before I bought the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...