Jump to content
SAU Community

Recommended Posts

That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

well if the steering wheel isn't straight that'll be your problem. there are two sensors up in on the steering column that tell the HICAS ecu that you are turning the steering wheel and which way. if your traveling along at at higher speeds, when HICAS becomes active, and because your steering wheel isn't straight the steering sensor is registering that you are turning the steering wheel, even though you really aren't, it will make the HICAS start steering. if your ok to do it yourself just pop the steering wheel off and line it up straight, or just take it back to the place that did the alignment and tell them to sort it out.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4755500
Share on other sites

Having a think the sensors aren't in the wheel itself, so the wheel could be on upside down and it wouldn't effect anything. Looks like I'll have to lock up the HICAS.

correct the sensors are mounted to the steering column and the steering wheel boss activates the sensors when you turn the wheel. you should be able to slide the whole steering wheel boss off and jump it over a spline. it will require a fair bit of persuasion to get it off though.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759332
Share on other sites

correct the sensors are mounted to the steering column and the steering wheel boss activates the sensors when you turn the wheel. you should be able to slide the whole steering wheel boss off and jump it over a spline. it will require a fair bit of persuasion to get it off though.

Okay, sweet. Thanks again Josh.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759336
Share on other sites

if you havent removed a steering wheel before, be VERY careful and dont remove the nut completely before you attempt to remove the wheel. leave it on a few turns so it doesnt smack you in the face when youre wiggling it off!

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759350
Share on other sites

Thing is, if the steering wheel wasn't removed immediately prior to this issue, it can't have moved on the spline.

Removing the wheel and re-orienting it will not correct the original source of the problem.

The rack centre position could be offset to one side, causing your problem.

You should turn the wheel from centre to lock in each direction counting the number of turns, if it is unequal in either direction, any adjustment should be made at the rack ends with the rack centred.

Then you can be sure that your rack (and therefore) steering column and wheel are centred correctly.

Good luck.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759796
Share on other sites

That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

what work did you have done to the suspension? height adjustment by any chance?

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759895
Share on other sites

if you havent removed a steering wheel before, be VERY careful and dont remove the nut completely before you attempt to remove the wheel. leave it on a few turns so it doesnt smack you in the face when youre wiggling it off!

Hahaha I've done it a couple of times so won't have that problem!

Thing is, if the steering wheel wasn't removed immediately prior to this issue, it can't have moved on the spline.

Removing the wheel and re-orienting it will not correct the original source of the problem.

The rack centre position could be offset to one side, causing your problem.

You should turn the wheel from centre to lock in each direction counting the number of turns, if it is unequal in either direction, any adjustment should be made at the rack ends with the rack centred.

Then you can be sure that your rack (and therefore) steering column and wheel are centred correctly.

Good luck.

Great post, thanks for that.

might also been the rack bushes too! if they are stuffed, it will cause the rack to move also. its possible its just jammed in the wrong position.

I only just had them done. If some things weren't done correctly can that lead to these issues?

what work did you have done to the suspension? height adjustment by any chance?

Bilstien coilovers, cambers kits and traction rods and all sorts of random shit. I really don't know a whole lot about suspension sorry. :( But definitely height has changed, it's certainly lower.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4760905
Share on other sites

  • 1 year later...

open your eyes before your mouth please

pull ur head in smartass, i was making a valid point about a possible scenario. which has nobody has proven otherwise or posted anything to the contrary. its entirely possible that if the front washed out on turn in, that the rear turning away from the corner could turn you off the road/track. maybe not a common situation but possible none the less.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-5918242
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...