Jump to content
SAU Community

Recommended Posts

Engine

Forged Pistons

Forged Rods

Performance rings

Balanced and blue printed block

Ported head

Billet crank

Kevlar timing belt

Tensioned valve springs

550cc injectors

HKS Cams

HKS Cam gears

HKS Silicon hoses

HKS Duel dump pipe

HKS 3 layer head gasket

HKS POD filter

GFB BOV

Engine resprayed candy apple red

Intake

Upgraded roller bearing turbo

Z32 AFM

R33 radiator

Big cooler

Thermo fans

Stainless induction

Powder coated black cooler pipes

Driveline

OS Giken custom clutch

Lightened fly wheel

2 way mechanical LSD (Cusco I think)

Fully adjustable JIC Gold coilovers

Exhaust

Blitz NUR-Spec 3" stainless exhaust

Interior gadgets

HKS incab duel stage boost control

HKS Turbo timer

HKS Boost gauge

HKS Stainless shifter

Momo steering wheel

Recaro adjustable back race seat

HUD (speedo on windscreen)

Black wired alarm

Keyless entry

Electric windows

Full stereo including sub and amp

Origional 180sx floor mats

ECU

Dr Drift tuned ECU

Suspension etc

Strut brace

Nolathane bushes etc

P1 Buddy light weight race rims

Upgraded cross drilled disks

Upgraded callipers

Project Nu race pads

Body

Car resprayed Polar White

C-West front bar

Buddy club side skirts (I think)

Vertex rear bar (I think)

Shaved rear wing

Type x tail light and centre

I've just paid a years rego.

If you'd like any info just ask.

I'm looking for $13,000

Will neg for serious buyer

The car puts out close to 250rwkw on an aggresive tune, I drive it around at 170rwkw because it's just used to get me too and from work.

n586867363_1826830_4443285.jpg

4435_85669702363_586867363_1826822_2892650_n.jpg

Link to comment
https://www.sau.com.au/forums/topic/283331-180sx/
Share on other sites

  • 2 weeks later...

G'day mate, it's an 89 model so it's a ca18, great on fuel and massive amounts of torque, it's above 600nm on a high tune.

I dont have reciepts for the work unfortunately due to a horrible house move where i ended up living in a shed for 4 weeks!

The turbo is a modified Garret roller bearing turbo, I'm only running 12psi as it's only used as a daily driver, it sure makes some noise when it's boosting!

Im located in Ballarat Victoria, about an hour from Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/283331-180sx/#findComment-4791155
Share on other sites

  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...