Jump to content
SAU Community

Recommended Posts

alright guys this might sound pretty retarted,but here it goes.IM looking to get a new exhaust system for my completely stock 34 i was wondering if anyone can give me info on wat i will need to look at buying,prices,websites where i can buy it from i will pay pretty decnt money for it too sound good without getting defected.also wat are your thoughts on those silencing exhausts???

thank you.

Link to comment
https://www.sau.com.au/forums/topic/283498-r34-exhaust/
Share on other sites

i just did a full custom exhaust on my NA r34,,,, which is pretty much ur only choice that im aware of if your car is 4 door and 4wd like mine,

i used,

-coby extractos 270$

-exhaust gasket, not genuine 45$

-2.5 inch mandrel bent pipe ~60$

-x-racing high flow stainless resonator 100$

-pro racing stainless high flow twin tip european style exhaust 150$

-removing old exhaust bending and installation labour was 450$

its as loud as F#$%!!! but they arent so strict on noise here, so you'll definately want a silenced exhaust or a multi core muffler installed before the actual exhaust and before the rear axle

ive found the 2.5 inch pipe to be good flow on the highway, no restriction on flow, but when cruising in town i think 2.25 would be a better diameter for the low rev range...

all those prices are in NZ dollars aswell, goodluck!!

Link to comment
https://www.sau.com.au/forums/topic/283498-r34-exhaust/#findComment-4769299
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...