Jump to content
SAU Community

Recommended Posts

I'm not totaly happy with my oil presure so I'm thinking an upgrade to the oil pump may be the go and after a bit of searching I have come across NITTO,and N1 and I'm thinking there may be more.

The NITTO was around $1200/1300 and the Skyline GTR NI $580 appart from the $ how big is the difference between these two.

Will the GTR N1 fit the 98 R34 GT-T and will there be a significant improvement over the OE GTT one in there now ?

I'm not modding this car, I only push it around a little bit occasionaly, I'm not $1300 bucks worth unhappy with the current pressure and it wont see the track while I've got it.

Having said all that summer is coming so soon would be the time to do this if I'm going to so any advice on this would be gratefully received.

Oh and while I think about it how hard / many hours in fitting to a 98 R34 GT-t.

Link to comment
https://www.sau.com.au/forums/topic/283924-oil-pumps-aint-oil-pumps-sol/
Share on other sites

I don't know how R34's work, but incorrect oil pressures (32's, 33's) are the result of a dirty pressure switch, I would first clean the switch (near the oil filter). As for fitting a new pump, its a engine out job. Others have reported the Nitto pumps are as good, if not better than the $2000 jap pumps.

If it's not going to the track, or be bouncing off the limiter, there are better ways to spend your money than getting track orientated pumps for a lazy daily driver.

Read this thread: http://www.skylinesaustralia.com/forums/N1...il-t283867.html

I definately wouldn't worry about the oil pump. To replace it you will need to take motor out and pull it apart (it is possible on car but still heaps of labour, balancer off, timing belt off, drop subframe, sump off).

You can get a second hand rb25 for less than the cost of an oil pump....

:P Thanks guys didn't realise how much info was in the Epic fail thread thanks for that , oil pressure sender cleaning will be done.

Just a bit more I came across this:-

NISMO OIL FILTER

FEATURES:

  • 21% LESS PRESSURE LOSS
  • 24% INCREASE IN FILTRATION
  • 10% LESS FLOW RESISTANCE
  • 37% INCREASED LIFE

PRICE: $49.95 EACH

And just wondered if there's any mileage with these claims or is it just manufacturers rhetoric ? reason I asked I noticed an overall slight drop when I changed the oil and filter last time the filter that was in was a Jap no name which I think may have come in with the car.

I'm using 10x40 Nulon quick flow full syn and a Nissan OE filter.

Edited by BASHO

All I can say is FARK THAT! I could be wrong, but with the 'shithouse' Ryco filters, I have no strange variations or delays in oil pressure (that said im going to start using Nissan ones for peace of mind)

IMO if you're going to spend $50 on the filter, add that amount to what you spend on oil and use Motul 300v or something.

I think it's all a load of crap, when theyre $8 each, just change it when you change your oil.. May as well use a genuine Nissan filter, theyre pretty much the same price maybe cheaper than the Ryco equiv.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...