Jump to content
SAU Community

Recommended Posts

I've bought injectors for my jeep stroker motor from them before. Real good customer service. I recently had the injectors cleaned and flow tested after running them for a couple of years, and they were closer in spec to each other than my nismo 740's I used to have. I think since they specialize in moving a lot of injectors, they get a lot of 100 or so if the same type, test them, match up the ones that flow the closest, and get pretty good results. I think they mostly deal with OEM applications though.

Were they a Hi Flowed injector or a standard item , high impedance I gather .

Cheers A .

Off-the-shelf drop in replacement (except for plugs, they were supplied), high impedance, 550cc's.

Same as Sards.

are CA18DET injectors bigger because they'd work?

no CA18det are low impedance, CA18de's are high impedance and they are only around the 290cc mark.

have a look here, the biggest drop in are 550cc but if you want to change the rail you can go up to 890/900cc

http://www.injectorsonline.com/

P.S. Just wondering why you aren't interested in wiring in the dropping resistor, i was under the belief that low impedance injectors are easier to control at low duty cycles?

Edited by D_Stirls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...