Jump to content
SAU Community

Recommended Posts

JUNBL muffler with 2 pipes coming out back. all on flanged direct bolt up to r32 exhaust. from cat back. heres a photo. didnt get a chance to polish it up but itl come up nicely. also has 1 tiny dent in muffler the size of a tiny stone.

http://i224.photobucket.com/albums/dd174/b...29082009070.jpg

chasing 250 for it all. ONO

also got a r32 gts-t bonnet for sale. 100bux small scratch up top nothing bad.

twin pillar gauge holder 60mm and another twin pillar gauge holder but 52mm. want 30bux each for em. brand new basically.

Drift brand steering wheel $30. good condition

2x old tyres. bfgoodrich tyres. 235/17. 10bux each for em. about 25% tread left on em. be good for a couple of laps at drift pracs. 15bux for both of em?

1x rear pod r32 gts-t 20bux? freshly painted black. dont ask where other 1 is coz i dont know

2x type m side skirts. 1 in ok condition the other is the same except the front peice of it is missing (drivers side). want 40bux for em. or 50bux for pods and skirts.

sub+amp+that little blue cable dunno what its called. want 10bux for the lot.

all prices are ONO. i got a big project coming up and need this stuff gone.

cheers all parts located in SA also

Edited by craig132
Link to comment
https://www.sau.com.au/forums/topic/285573-r32-gear-for-sale/
Share on other sites

bump.

rear pods/ side skirts sold payment pending

60mm gauge holder sold payment pending

Racing passenger bucket seat for sale similar to JJR brand for sale, perfect condition with rails to suit r32 gts-t. all ADR approved. $140 and your stock passenger seat ONO

exhaust down too $220 need it gone asap

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...