Jump to content
SAU Community

Recommended Posts

Hey guys, I'm after your advice. I have a Stagea 260RS with an RB26DETT from an R33 GTR. 2 weeks ago the car just cut out. We found that the ignitor module was dead, so ordered a new one from Nissan for $800! The car ran fine for 2 weeks and then the same thing happened again last night. Not happy! Any idea what might be killing the ignitor module? I pulled out the coil packs and measured the resistance on the primary and they were all around 0.8ohm, which looks good. I checked the grounding, power supply and also checked I was getting a good signal from the ECU and it all looks good. Any ideas? I really don't want to put another ignitor in there and then have it die on me again.

Link to comment
https://www.sau.com.au/forums/topic/285883-car-has-fried-2-ignitor-modules/
Share on other sites

Some questions:

How have you diagnosed that the ignitor is "dead"?

Have you substituted a set of known working coils with you ignitor? While you are at it, substitute a known good harness also. Double check the earthing eyelet is both well connected to the harness and is cleanly ground?

I assume you're not running an HKS Twin Spark (or other CDI pack)?

Finally, I don't pay heed to the Nissan manual's method of diagnosing by measuring resistance - I've had failed coils return exactly the same readings as good coils.

PS - there should be some warranty on the ignitor from Nissan.

Bad ground. Check you have at least 2 good grounds from the engine to the chassis. Loosen them off, give them a wiggle and tightten them up again.

A bad earth causes the ignitor to not be able to switch max current to the coils. It can also cause the ignitor to burn out as the earth signal drifts around.

Thanks for the feedback guys. I don't have a set of coilpacks to swap over, but I should be able to get some from my mechanic. When the first ignitor died, he just swapped it over with a known good one, and it all came good. So no need to investigate any further. I was away last week, so just bit the bullet and bought the new one to get the car going for my wife.

I'll take a good look at the earths tomorrow. Might need to look into that Nissan warranty... thanks

My money is on a dodgy coil. Sometimes a newer (i.e. stronger) ignitor will mask a bad coil for a while. Borrow a set of known good coils and see if that makes a difference. If you are still using the original OEM coils it may be time for an upgrade anyway.

Well, I've bitten the bullet and ordered a set of Splitfire coilpacks. If they're not dead already, it's only a matter of time, so I'd may as well replace them now. Fingers crossed this fixes the issue.

  • 1 month later...

Well it's been a bit over a month since I replaced the coils and the car has probably done over 1000km and has been running great. Until today.....

Exactly the same issue. Engine just cut out. I haven't had a look yet, but I'm 99% sure the ignitor module is fried again. Not happy at all!! I have bought 2 ignitors now ($1500), plus a set of Splitfire coil packs and now it looks like I'm up for another ignitor :ermm:

I'm not sure if it's a coincidence, but all 3 times it has died under similar circumstances: cruising down a hill (overrun fuel cut would have kicked in), get to the bottom, go to accelerate and find it is dead. It has a Vipec ECU (has been in there since November/December last year without any problems). I've emailed them already to find out if they have any ideas.

Well it's been a bit over a month since I replaced the coils and the car has probably done over 1000km and has been running great. Until today.....

Exactly the same issue. Engine just cut out. I haven't had a look yet, but I'm 99% sure the ignitor module is fried again. Not happy at all!! I have bought 2 ignitors now ($1500), plus a set of Splitfire coil packs and now it looks like I'm up for another ignitor :)

I'm not sure if it's a coincidence, but all 3 times it has died under similar circumstances: cruising down a hill (overrun fuel cut would have kicked in), get to the bottom, go to accelerate and find it is dead. It has a Vipec ECU (has been in there since November/December last year without any problems). I've emailed them already to find out if they have any ideas.

What new wiring has been done in the engine bay/car. Has there been any new sections that were soldered? I had a similar thing happen to me where an electrical short fried my CDI (Autronic) I pulled the coil wiring apart and found a solder joint that had a little peak which rubbed through the wire insulation and bang. Although mine didn't cut out entirely but was running on 2 cylinders.

Have a good look at the wiring- i know it's a pain in the ass but hopefully you can remove the wiring as the cause if you find nothing?

Hope that helps.

What new wiring has been done in the engine bay/car. Has there been any new sections that were soldered? I had a similar thing happen to me where an electrical short fried my CDI (Autronic) I pulled the coil wiring apart and found a solder joint that had a little peak which rubbed through the wire insulation and bang. Although mine didn't cut out entirely but was running on 2 cylinders.

Have a good look at the wiring- i know it's a pain in the ass but hopefully you can remove the wiring as the cause if you find nothing?

Hope that helps.

my bet is the coil loom...these things get very brittle with heat and this hardens the insulation which causes it to flake and expose the conductor. This shorts the output causing extremely high current which frys the power transistors in the igniter.

I spent a fair bit of time going over the loom last time I had this problem. All of the connectors are in good condition. None of them have become brittle yet. I also spent some time measuring for shorts while shaking the loom to see if there were any problems. Very frustrating problem this one...

I spent a fair bit of time going over the loom last time I had this problem. All of the connectors are in good condition. None of them have become brittle yet. I also spent some time measuring for shorts while shaking the loom to see if there were any problems. Very frustrating problem this one...

its not in the connectors...im talking about the coil loom itself. You will not be able too see the damage (if any) unless you remove the grey tape. When you have installed the coils you may have moved the loom around separating the possible damage site. With engine movement the damage has moved close enough to short out again. Ive seen this problem before and it normally occurs at the bend in the loom near coil 5.

not saying this is 100% what it is but id untape the loom and do an inspection.

Edited by DiRTgarage

Well the car is running again. I cut open the ignitor module and found the PCB track to the ground pin had burnt out. I soldered in a piece of wire and it's running again. Who knows how long it will run for..

The question is, why is the ground track on the PCB burning out? This is the only ground for all 6 transistors and it burnt out after number 6, hence I lost all transistors.

OK, as promised here are the pics of the ignitor modules. I owe a thanks to FastRotor who's been offering me advice about this problem.

Bit of a how-to guide:

1. Cut open the box around the top, about 5mm in from the edge. I used a Stanley knife and only managed to cut myself twice :P

2. The inside is filled with this sticky silicone-like clear substance. You can poke your multimeter through it to determine the dead track. You can see my dead track on the top left (it's a bit burnt). This is where the last transistor connects to the ground pin. The current from the emitter on each of the 6 transistors flows through this piece of track.

3. Peal back the sticky sealant.

4. Solder a bit of wire over the broken track. The solder Nissan have used is quite hard and requires a fair bit of heat to melt it. I had my soldering iron set to 400 degrees to melt it.

5. Once you're happy with your wire you can place the sticky sealant back down over the top of it. Be careful of the little silver leads they are very fragile.

Quite an interesting design inside that little box. I've never seen transistors that look like that and definately haven't seen a board covered in that sticky silicone stuff.

post-9210-1255318307_thumb.jpg

post-9210-1255318318_thumb.jpg

post-9210-1255318409_thumb.jpg

So I guess the question now is: what fried that little piece of track.

It's got to be one of 2 reasons:

-Too much current

-More than 2 transistors on at once. The ECU I'm using runs wastespark, so there are 2 transistors on at once. This means twice the current through that track. Heaps of people have run this before, so I doubt it's a problem. However, if for some reason I got a short on the input or an ECU fault, I could potentially switch on 4 or 6 transistors.

-Short across the primary on one coil pack. If I got 12V shorted across the primary then you'd have a short through one of the transistors. Would the single transistor fail instead of the ground link? I've stripped back the loom and it looks OK, the coil packs are brand new, so this doesn't seem like a likely cause. I've also measured the resistance between ground and the battery and it is 0.1ohm, so looks good to me. Unless there's a loose connector somewhere. I tightened the ones I could access last time I had this problem.

-Higher alternator voltage. That combined with wastespark would mean more current. The max voltage I saw today in the logs was 13.87V so that looks OK.

-Too much dwell

-I just went for a drive and had a look at the log. The dwell is sitting at 1.8-1.9ms with a max of 2.7 at some point, so it looks OK. A dodgy CAS might cause the dwell to go high at some point..

-One of the inputs is jammed on for some reason. I guess this could cook the ground track or the transistor or the coilpack. Who knows?

So that's all I can think of. Anyone got any other ideas? I think I'll fix my other broken ignitor and drive around with it in the glove box in case of an emergency. :P

So I guess the question now is: what fried that little piece of track.

It's got to be one of 2 reasons:

-Too much current

-More than 2 transistors on at once. The ECU I'm using runs wastespark, so there are 2 transistors on at once. This means twice the current through that track. Heaps of people have run this before, so I doubt it's a problem. However, if for some reason I got a short on the input or an ECU fault, I could potentially switch on 4 or 6 transistors.

-Short across the primary on one coil pack. If I got 12V shorted across the primary then you'd have a short through one of the transistors. Would the single transistor fail instead of the ground link? I've stripped back the loom and it looks OK, the coil packs are brand new, so this doesn't seem like a likely cause. I've also measured the resistance between ground and the battery and it is 0.1ohm, so looks good to me. Unless there's a loose connector somewhere. I tightened the ones I could access last time I had this problem.

-Higher alternator voltage. That combined with wastespark would mean more current. The max voltage I saw today in the logs was 13.87V so that looks OK.

-Too much dwell

-I just went for a drive and had a look at the log. The dwell is sitting at 1.8-1.9ms with a max of 2.7 at some point, so it looks OK. A dodgy CAS might cause the dwell to go high at some point..

-One of the inputs is jammed on for some reason. I guess this could cook the ground track or the transistor or the coilpack. Who knows?

So that's all I can think of. Anyone got any other ideas? I think I'll fix my other broken ignitor and drive around with it in the glove box in case of an emergency. :P

dont forget about the base current from the ecu to switch the transistor. This current also goes to ground through that track.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...