Jump to content
SAU Community

Recommended Posts

:P

I am new to this forum ,but would like to share my method of converting the cluster from the original orange lighting, to new fresh LED lights

I haven't taken any pictures of the process of taking the cluster out, and pulling it apart, but will be happy to explain how to, if someone gets stuck.

Apart from that everything else I tried to capture

BEFORE YOU TAKE THE ARROWS OFF, MAKE SURE YOU MARK OFF THE POSITION OF THEM, WITH A SMALL DOT, WITH A MARKER(I simply moves each arrow until it stopped in a certain direction and put a mark there)

1. TO TAKE THE ARROWS OFF, I USED 2 BUTTER KNIVES, SLID THEM UNDER THE ARROWS AND TWISTED THEM IN OPPOSITE DIRECTIONS, TO FORCE THE ARROW UP

2. SOMETHING TO NOTE!!! THE CLUSTER USES NEGATIVE TERMINALS TO SWITCH THE LIGHT ON AND OFF

VOLTAGE IS QUITE LOW, COMPARING OTHER 12 V CLUSTERS!!! THE VOLTAGE IS 7.6 VOLTS, THEREFORE I USED 150 OHM RESISTORS!!!

DO NOT USED RESISTORS WHICH SCOME WITH LEDS THAT YOU BUY OFF EBAY!! AS THEY ARE 680 OHMS, THE LIGHTS WILL TURN OUT TOO DULL!!!

3. THE LEDs I USED HAVE A HIGH CONCENTRATION OF LIGHT, SO I FILED THEM DOWN TO A FLAT TIP, WHICH MADE THE LIGHT SPREAD MORE (NOT THE ARROW LEDs)

4. BEFORE YOU UNPLUG THE CLUSTER OFF, MAKE SURE YOU TEST EACH SOCKET OF THE BULBS, WITH A VOLTMETER, TO FIND WHERE THE POSITIVE AND NEGATIVE TERMINALS ARE, AS LEDS NEED RIGHT POLARITY TO WORK

5. I ALSO CHANGED THE HIGH BEAM TO LED AND INDICATORS TO LEDS, BUT PLEASE NOTE, USE 300 OHM RESISTORS FOR THEM, AS THEY ARE 11.2 VOLTS

Here's what I've done, to achieve RED arrows, or you can do it with just about any color LEDs

Basically the prism you will find inside the cluster had 4 extensions coming out to 4 bulbs, to collect as much light as possible, what I've done is cut them and attached a red LED to the cut part of the prism.

I just MELTED the led contacts into the plastic, by pushing onto it with a soldering iron, But you can hot glue it if you like

As for the fuel/temp prisms, there's only 1 extension to the prism, which I also cut

Here's the photos

post-65692-1252055041_thumb.jpg

post-65692-1252054735_thumb.jpg

THIS PHOTO HERE shows that the RED light is reflected by the prism, and shot upward towards where the arrow is

post-65692-1252055135_thumb.jpg

This is what I've done with the LED's Just prepared them, and put them in pairs of 2, to use in the positions of the bulbs

As for the REVS dial, with a bit of red on the end, I used a red LED, so it slowly fades form white ro red in the end

post-65692-1252055396_thumb.jpg

Here's what the cluster looks like from the front, with LEDs soldered in

post-65692-1252055536_thumb.jpg

And this photo has both LEDs soldered to the circuit + the prism with led attached (I used a computer IDE cable, cus the wires from it, and extended the contacts to the back of the board)

post-65692-1252055701_thumb.jpg

And here it is with power to it, and TAPE OVER THE RED LED, NOT TO GET THE RED MIXING WITH THE WHITE

post-65692-1252055909_thumb.jpg

With facia on, and power on!

post-65692-1252057885_thumb.jpg

AND THE FINAL RESULT!!!!

post-65692-1252057964_thumb.jpg

GOOD LUCK IF YOU EVER GET TO DO IT,1 IT'S REALLY NOT THAT HARD

Link to comment
https://www.sau.com.au/forums/topic/286597-stagea-m35-nm35-led-conversions/
Share on other sites

thank you... i hate my orange lights....

is it possible to change the lights behind the nav buttons and the lights in the boost volt and temb gauges?

I'll be doing a CD Radio Nav conversion next week, so I'll take detailed pics

Im sure they are just SMD LEDs (Little square ones), that just need to be changed over.

I'll keep you guys posted

Nice work man!

Would love a step by step to remove the cluster (I have found I can damage stuff easily :P )

I too like my orange lights, but the one behind the gear display has gone out and need to be replaced.

Nice work man!

Would love a step by step to remove the cluster (I have found I can damage stuff easily :domokun: )

I too like my orange lights, but the one behind the gear display has gone out and need to be replaced.

Thanks!!

I've posted another topic of how to remove the cluster out

Here's a link

http://www.skylinesaustralia.com/forums/St...va-t286664.html

CENTER CONSOLE LED CONVERSION INSTRUCTIONS

Just a follow up, with some instructions on how to remove the center panel, and change The heated seats button Lamps to LEDs, as well as the backlight for the shifter

FISRT MAKE SURE THE SHIFTER IS IN DRIVE, FOR EASY ACCESS

Here's what you have to do first, unclip the bottom plastic cover from underneath the shifter, slide it down and take out the metal C Clip

post-65692-1252126724_thumb.jpg post-65692-1252126768_thumb.jpg post-65692-1252128608_thumb.jpg

Now the whole center panel should freely pop up and come off

post-65692-1252128652_thumb.jpg

This is what it looks like from underneath, with everything attached to it, NOTE IN THE MIDDLE, THERE'S RED AND BLACK CABLE WITH A TWIST SOCKET BULB, THIS IS BACK LIGHT FOR THE SHIFTER (T10 BULB)

post-65692-1252128805_thumb.jpg

Now once you've unclipped all the connectors and taken out the center panel, take out the Heated Steate switches, by undoing the clips with a flat head screw driver

post-65692-1252128860_thumb.jpg

The switches have 2 clips on both sides, you have to take out the center part, with flat head screw driver again (Be careful not to break the plastic, its a little tricky, if you break it, dont worry, nothing that supe glue can't fix! :(

post-65692-1252128934_thumb.jpg

You will find, there's 2 ligh bulbs on the switch, 1 12 volt hallogen bulb, and 1 LED (Both of them have 12V Source, LED Bulb has a resistor soldered onto it already)

post-65692-1252129041_thumb.jpg

YOu have to remove the LED and the Light bulb out of the rubber housings, BUT REMEMBER THE POLARITY OF THE LED

post-65692-1252129133_thumb.jpg

I've basically put 2 LED's instead of the original bulbs with 300 ohm resistors. BULBS HAVE THE VERY END TERMINAL, BLUE WIRE AS A NEGATIVE!!!

I've also filed the LED's, to make the light spread more, and to make a bit more room, for the switch to work properly

This is what it looks like with a RED LED for the backlight, and WHITE LED for the indicator switch

post-65692-1252129326_thumb.jpg

GOOD LUCK

;)

post-65692-1252129204_thumb.jpg

G35 set up?

more info plz?

If you go to www.ebay.com <---- US EBAY

Type up "G35 Navigation"

Plenty of second hand units with english navigation units and radio that works here, as US frequencies are the same as here

Basically infiniti, is same as skyline, just a re badge

It costs a fair bit to get it here, but in the end its all worth it I reckon

I wont have the Jap writing anymore, and will have the Fuel Consumption display as well....which is good... ;)

Glad you guys liked it!

Soon I'll be changing the CD RADIO and NAV lights, after my INFINITI G35 Setup comes in

Then I'll upload some more steps on DIY

This guy's right! No TV on these but the Nav stuff should work. English buttons if you want to go that way. Full BOSE system also if you want to go that way.Why haven't we heard this before? Around $550 USD

Nissan6CDG35NAVP.jpg

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...