Jump to content
SAU Community

Recommended Posts

Ok so i spoke to a mate of mine who is a mechanic he said that a scremer pipe will increase boost response time because the turbo keeps spooling/spinning somthing about there being no back pressure. can someone confirm/deny this because this would be a performance increase.

i would like to get into drift raceing i just dont have the money but little things like this i can get made up and use them when i start drift raceing and remove them when i wanna drive on the road.

the effects will be minimal over a decent exhaust with it all plumbed in.

well i have a full 3inch into 4inch cannon from the turbo back would you consider that a decent exhaust?

Edited by R33Gtst Driver
planing on doing it with the stock turbo? if so you will still only get 200kw and 3" will be fine for that and it should still be fine at 300kw.

i have a high flowed t3/t4 turbo already but im planning on geting a g35? turbo i thinks its called i will be makeing 4-500kw or more for now i think thats what my mate is makeing im pretty much just copying what he has got

no gt35 is going to give you 4-500kw. it is not a turbo capable of that and your engine wont like it either.

yeah im not sure about the name of the turbo im pretty sure my mate said it was a g35 turbo he is using? allthou i cant find any info on it so i probley have got the name of it wrong

Edit: also i ment hp not kw

i think this is the one he has http://www.cimotorsports.net/motor-sport-p...rbocharger.html or something similar. so what the reason my motor wont like it?

Edited by R33Gtst Driver
The stock engine internals are only so strong, you are asking them to deal with 200kw or more than the factory 187. it may last for years it may last a week.

i thought you were gonna say it wasnt big enough :cool: thanks for the heads up but im aware of the internals factor im not to worried about it thou as im planning to build a stronger motor anyway

i just realised this would be a good place to ask a question so here goes basicly i wanna make 600hp - 1000hp in my skyline with a really good response. the responsiveness is more important to me then the power but i would still like to have a alot of power what turbo and engine mods would you guys suggest? i have been looking at turbos from here http://www.turbobygarrett.com/turbobygarre...ers.html#medium but i cant make my mind up any hlp would be apprecitated

Edited by R33Gtst Driver
at no point should you combine i want 600-1000hp and response is important. its not going to happen. 600hp is getting to the upper limits of a 1.0 rear T04Z and thats not going to be on full boost till 4500-5000 or later.

ok well i dont know much about what im doing wwith upgrades. i just want huge amount of power and a decent spool time i figured big lag and nos shots were required for 7-800hp or more.

whats the to4z hp rated to? as thats sounds good to me and am i better of going for a cutoms turbo like gt35/gt42 or gt45 over a t04z

ok well i dont know much about what im doing wwith upgrades. i just want huge amount of power and a decent spool time i figured big lag and nos shots were required for 7-800hp or more.

whats the to4z hp rated to? as thats sounds good to me and am i better of going for a cutoms turbo like gt35/gt42 or gt45 over a t04z

The circuit car that im driving is a 32 v-spec gtr v-spec, fully built engine and drivetrain with a custom t04z external wastgate/screamer pipe.

Puts out 420awkw at 1.5 bar, makes the best sound in the world. I really think you need massive power to make an screamer pipe a worthwhile/credible thing.

I havent fully read your thread, but i cant help but thinking your modifying the wrong car. The to4 on the rb26 has a significant amout of lag, starts pulling from 4300 and then rockets from 5 to 9,000rpm in the blink of an eye!

Wouldnt have much of a rev range without massive cams and strong internals.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...