Jump to content
SAU Community

Recommended Posts

if ant actually winds his up, im guessing it'd blow both nathan and probally danny into the weeds, all be it momentarily before it dies itself as its still got a stock crank, ant was telling me he'll be happy with around 600..

danny's should in effect cream nathans car..

Link to comment
https://www.sau.com.au/forums/topic/28725-it-runs/page/2/#findComment-596510
Share on other sites

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

if ant actually winds his up, im guessing it'd blow both nathan and probally danny into the weeds, all be it momentarily before it dies itself as its still got a stock crank, ant was telling me he'll be happy with around 600..

danny's should in effect cream nathans car..

The problem with ants car is gearbox.

To that last statement i say it comes down to drive skill, not cheaque book racing. ie i wonder how 1 car got tuned b4 another :Oops:

hopefully no more ****ups danny. i Bet u are giving it to shane even more now that things are almost done, and the rx4 is further away

Link to comment
https://www.sau.com.au/forums/topic/28725-it-runs/page/2/#findComment-597339
Share on other sites

I think Anth and myself are both aiming a little higher than 600rwhp,we both have standard cranks with lots of work been done to them and yes this is the weak point in both motors as all other parts have beem replaced.we do not see this as a major problem as there are many cars over east with high hp built on standard cranks,without failure,we may be wrong but only time will tell.As for check book racing all forms of racing cost lots of money,time ,effort and sacrifice by all involved,now lets thrash them and have some fun.

Link to comment
https://www.sau.com.au/forums/topic/28725-it-runs/page/2/#findComment-598647
Share on other sites

  • 3 weeks later...

yeah it ran an 11.9 ?? i think

on another note ant needs a new box

Danny keep your R locked up otherwise some italian men might accidently borrow it overnight before returning it with a much less rattly gearbox :D

/me mutters something about nd4spd as he wonders off.....

P.S when do i get the pleasure of featuring it ? :)

Link to comment
https://www.sau.com.au/forums/topic/28725-it-runs/page/2/#findComment-617966
Share on other sites

Well the decision has been made something is not right in the motor and we are going to pull it down and check whats happening.Since picking the motor up from the last so called performance workshop the motor only had 90psi combustion presure and the assumption was made that this would increase once the motor was started but this was not to be the case.Will keep you all posted but it look's like were starting from scratch again,here's hoping it will only take a few weeks to rebuild and will be back on the track soon.

Link to comment
https://www.sau.com.au/forums/topic/28725-it-runs/page/2/#findComment-618594
Share on other sites

Jesus Christ Danny. I feel so bad for you having been told alot about what the GTR has gone through to get to this stage and to now hear about this is just pain.

I hope you take to some people because heads need to roll. Seeing as how your nearly as big as me im sure this will be an easy job.

In all seriousness i think legal action would be a good way to go here. Youve been screwed around too much for this to be just a trivial matter anymore.

I really hope to see you back in action soon and the best of luck with everything with this rebuild.

Cheers and good luck with the head kickng

Tom

Link to comment
https://www.sau.com.au/forums/topic/28725-it-runs/page/2/#findComment-618603
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...