Jump to content
SAU Community

Complete Rb26 Long Motor With Forged Pistons, N1 Water Pump, Oil Pump Etc

Antimatter
 Share

Recommended Posts

Antimatter Experienced

Antimatter

Posted
Posted

Ladies and Gentlemen

I am just looking for EOI at this stage as I have this motor that has become a bit of an orphan.

RB26DETT (05U) with forged pistons fitted in japan

Engine was stripped down due to conrod bearing issue

Complete reco crank, rods, bearings etc (done by ben @ racepace)

Block was cleaned and crack tested, new welsh plugs

N1 oil pump and water pump

Vernier cam gears

Reco head with new tomei metal head gasket

More details on other machining and work available

Engine is a complete long motor from cam covers to sump (no turbos or inlet manifold - but have turbos available if need be).

Looking for $5500 or thereabouts (bare in mind wreckers are asking 5k for "unknown" used engines)

PM or email [email protected]

Engine located in Vic but can arrange freight anywhere.

Thanks!

Antimatter Experienced

Antimatter

Posted
  • Author
Posted (edited)

no idea on the pistons - some forged jap things.

Block is R32 > Crank is R33 / wide oil pump drive.

(Crank has done no k's since overhaul)

what pistons being used, also which model engine is it?
Edited by Antimatter
Gtir-keiron Community Regular

Gtir-keiron

Posted
Posted (edited)

looking for a built motor as i can t be assed to build one my self plus its cheaper to buy some one elses lol.

More info would be nice.

cams cam gears head work pistons rods what bearing kit was used head studds and so on and so on water pump oil pump yada yada.

Edited by Gtir-keiron
Antimatter Experienced

Antimatter

Posted
  • Author
Posted

Hi

rods, cams, head & headbolts are all standard

N1 oil and Water Pump

Tomei Head gasket

ACL Race Bearings.

PM or email Me for more details

looking for a built motor as i can t be assed to build one my self plus its cheaper to buy some one elses lol.

More info would be nice.

cams cam gears head work pistons rods what bearing kit was used head studds and so on and so on water pump oil pump yada yada.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...