Jump to content
SAU Community

Recommended Posts

hey guys how are u

benm: unless u have something huge mounted between youre plenum and strut tower, ull have room

B-MAN: piping doesnt cost very much, so buying without will not make much of a change at all....

BANZAI: yes, u can buy one! when suits you?

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Player_Hater: yes we do! but u need to come round to our factory to have the bracket made individually....when suits you?

BMAN: they have a internal downpipe that directs the fumes into stainles steel mesh where it condenses..theyre not just hollow cans like those "bargain" 90 dollar autobarn ones.....

BMAN: i talked this over with parents and money order is our preferred way to go...so yeah if you wanna hook one up at youre local post office i can have it posted out to you the day i recieve the money order :(

is that ok?

I think that most people who have done a lot of internet buying and selling would be fairly disenchanted with cod. It is comparatively expensive to use, doesnt give any real guarantees to the buyer, and if it's not picked up the seller has to wear the cost both ways .

yeah guys a money order sent thru registered mail is the best way to go. its easy, and if u send it via registered, if it gets lost in transit u can cancel it, get a refund, and we can start again. COD just introduces a lot of hassles.

i am sending 2 kits off to queensland today, after recieving a money order just yesterday. its really a very short turnaround time, and it saves me having ppl say "ok i got it, but i cant get the money off for a few days/i get paid next week/i got a speeding fine etc.

its just easier as you get the kit as soon as u show u have the $$......less hassles for everyone....

yeah, well i guess if its all the same, money order is cool too?

my dads company is making these, im not getting them for free...hes got a lot on his plate and is doing this for me as a favour and to help you guys out. he just would like to see a money order before he ships a faitly intricate and time consuming part to the other side of australia...and thats fair enough id say.

im sending 3 kits to brisbane this afternoon, no probs.

Just making sure...

These kits...

Have EVERYTHING needed to mount them yourself in a short time?

No fabrication needs to be done?

Just mount it and connect the hoses, correct?

Have u installed these on an R33 yet?

Anyone?

Not doubting, just want to be certain

Just for interest

Mon 12/1/04........GT-spec15 pm'd me his name & addy for money order

Tues 13/1/04.......Sent off money order, ord mail

Thurs 15/1/04......pm received acknowledging receipt of m.o. and promising to send oil can

same afternoon.

Assuming all is well, should arrive Mon or Tues........Will repost when it arrives

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...