Jump to content
SAU Community

Recommended Posts

I just did some wheel alignment near my office today.

Not very happy with the job... the car doesn't pull left or right which means it's balanced, however..... my steering wheel which used to be straight now isn't straight!!!!

Can I just pull out the steering wheel boss kit and turn it a notch to make it straight, or does the alignment had to be re-done with the steering wheel hold straight??? Will turning the boss kit a notch gonna stuff up HICAS alignment?

Anyway I'm gonna bring it back to them tomorrow and ask them to fix it. If they still can't do it, I'll never go anywhere near them anymore... :)

Dun worry abt it... I went back to the shop tell them what happened.

They switched one of the rims front to rear on one side yesterday, because one of the rims bounced a bit more on the balancer due to perhaps hitting a pothole and bent it a bit.. Got it swapped back again... now steering wheel seems to have straighten up again...

Turned out just bias in tyres due to uneven wear front and rear. They should have swapped both sides left-right not just one side.

if u dont have airbag steering wheel then rotating the wheel straight wont affect the hicas.

I drove the car again and find that steering wheel still not dead straight... tried to move the boss kit a notch to compensate... and see what happens tomorrow..

sometimes it's kind of funny. you move one notch to the left or right you just can't get it straight, like the boss kit mount requires an extra notch in the middle to make it straight... any other ideas?

RS73, that's a common problem when the alignment is done by a shop that hasn't centred the wheel properly before doing the alignment. Basically you align the wheels to match the steering wheel, not the other way around! I would have taken it back to the shop and told them to fix it.

I got a 4 wheel alignment done for $60 at Goodyear in Castle Hill, and it was the best (not to mention the cheapest) 4 wheel alignment I've ever had done. It's hella out of my way but I'm going back there to re-align the front end since I've put in new castor rod bushes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...