Jump to content
SAU Community

Recommended Posts

Hey Everyone,

I thought i was never going to do this but as I am currently having financial difficulties I need to sell my project.

The car is a Ford Corsair GLI 1990, which has been converted to house the rnu/hnu12 Awd Attesa System found in Nissans like the GTR.

The cars has had a lot of custom work done do it. From the complete rear Sub frame to house the rear diff to run awd, to the entire front end which has been converted to the RNU/HNU12 Bluebird.

The car as it stands is ready for the engine and drive train to bolt in, the only thing I have not worked on yet is the fuel system. I have ready a fuel cell, pump and surge tank for the car.

The car has been resprayed black and is very clean, although thanks to the dust storms it is not at the moment, the engine is having a serive, all timing as well as the waterpump. Also the head and sump when inspected were very clean.

The car also comes with a number of spare parts which include:

-Spare HNU12 Bluebird Cross member/Lower Control Arms/Swaybar/Front Bar/Extra headlights/ few sets of HNU12 Foglights.

-Spare Wiring Looms for RNU12 (CA18DET)

-Fuel Cell (Pressure tested)

-SR20DET (Approx 74thousand km as per dash from halfcut)

-HNU12 Awd Manual Gearbox

-Short Shifter (possible a Nismo item)

-Tailshaft

-Genuine Nissan Gasket rebuild Kit

-3 rear diffs (R180 longnose 3.7Ratio/R180 Longnose 4.11Ratio/R180 Shortnose 4.11 Ratio from Gtir)

-HNU12 TopMount intercooler

-Strengthened rear drive shafts for Gtir Diff

-Front Driveshafts from HNU12 Frontcut

-Complete rear Rnn14 Gtir Rear Sub frame Setup

-Fuel Cell

-Surge Tank

-Bosch 044 Fuel Pump

-Spare Dash

-Spare Door trims

-Front Seats

-Recaro Seat Rails custom made

-Spare Brake Booster and slave

-Spare Clutch Booster

-Custom Intercooler Piping for FMIC

-Number of brake calipers

-Number of engine mounts

-spare shifter linkages from halfcut

-Spare HNU12 Front Bar and support

-HNU12 Radiator

-Spare Plumb back BOV and intake piping

-Spare Peddle set up

-16" ROH Chicane 3 piece wheels

-Spare complete set of Nissan U12 Trx Wheels with rubber

-5Stud hub conversion for front

And I'm sure there is alot more which i have missed.

Guys this is an opportunity to own something that is very unique and possible the only one of its kind. This car has the potential to be a quick car and will not attract alot of attention from the police.

I do not want to seperate any parts, I want to sell absolutely everything as a package.

I am looking for around $13,000 and I am still loosing out a fair bit. Let my loss be your gain and own something like no other.

I can be contacted via email or phone for any questions or inquiries

[email protected]

Or the mobile 0434 193 766

Note the car does not come with the strut brace or Recaros.

Cheers

dscf0147p.jpg w576.png

21092008183.jpg

08092008182.jpg

p1020233t.jpg

p1020222k.jpg

p1020221.jpg

p1020220w.jpg

p1020219.jpg

p1020218.jpg

p1020216a.jpg

28122008078vz7.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/290414-fs-project-awd/
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
    • And now the bloody flapper is jammed slightly open. Lazy as all f**k in 3rd-5th (very hard to convince it to make much boost before you run out of revs), but will make 12 psi in 1st, which shouldb't be possible with a 5 psi spring and controller set to <10 psi. Methinks I'm lucky it jammed where it did, rather than fully closed. It's actually a well weird situation. Careful examination of what's happening in the back of that housing when the gearbox comes out and all the other stuff (injectors, AFM retune) is supposed to be done, next week.
×
×
  • Create New...