Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

im in melb i can come pick it up also need the glove box front sway bar heater core unit inside the dash all the carpet boot trimming charcoal canister and air box and snorkel and drive window switch no 0403011187 thanks mate really need all these things

Hi, have you still got your tail lights?

Where can i pick them up?

Thanks DAnnie

so i have decided to wreck my r33 instead of fixing it after crashing it. everything for sale is in good condition unless stated otherwise. listed below is everything i can think of but if you need something not listed pm me or call on 0400119068. all interior parts are ready now (12/10) and will have things like motor and gearbox out by the end of the week. i will post pics up on request. feel free to make an offer but im not in a hurry to sell so dont bother low balling!! cheers, Shane

gcg turbo- sold pending payment

engine (inluding front facing plenum)-1300

gearbox-1500

front brake set up (rotors and callipers)-350

back brake set up-150

front subframe-250

steering rack-100

apexi coilovers (adjustable damper)-550

rear subframe + diff (shimmed)-500

front seats-200

rear seat-50

pedals-50

passenger door-120

drivers door (panel damaged, good for window and interior)-70

spare driver door (bought it to fix the car)-100

spoiler and boot-200

seat belts-100 the lot

s2 head lights. (2x left and 1x right)-250 each

fuel tank-50

tailshaft-100

heavy duty clutch and flywheel-100

brake master cylinder/booster-100

front 1/4 panels-120 each

side skirts (right side one slighty damaged)-50

white line swaybar-200

full exhausted system including front+dump pipe, high flow cat-500

big injectors-300

split fire coil pack-300

roll cage (half cage with side intrusion bars made by brown davis)-1000

17inch g-max rims (no tyres)-500

loom-100

tail lights-60

starter motor-40

defi water temp and oil temp gauge + defi control unit (missing oil temp sensor)-400

speedo cluster with 106k on the clock-150

would you have the round thin plate with a wire ribbon that sits behind the steering wheel that plugs into the airbag computer is about 2 or 3 mil thick and about 100 mil across is black with yellow info sticker on it if you have how much with postage to tassie thanks you can contact me on 0408802254 or pm on here your call

  • 2 weeks later...

Ill take the seat belts if they aren't already gone. Id also like some interior trim (handbrake boot, gearstick boot, carmats...) you name your price

  • 2 months later...

hey mate

i am after a piping that goes from the ic piping to somwhere (i dont know) near the stock bov.....

here is what i am after

post-37912-1268351673_thumb.jpg

if you have it them pm me please

  • 3 weeks later...

Hey mate i know its an old post,

But just wondering if u hav any of these parts i need??

- Frount passenger side quater panel

- The inner Frount gard Lh side were the cooler piping

goes thro and were the head light bolts up

i need that whole section

- S2 LH side, headlight

- Radiator suport bar

- frount reo bar, infrount of cooler

Any help would be much appreciated

if u hav any of the above send us a msg on 0403 236 931

cheers troy..

  • 2 months later...

im after the Heater AirFlow Direction Mode Actuator (underneath the dash passanger side above centre heater box) & a Heater Temperature Mode Actuator (driverside on the heater box pedal lil black box)..

if u got both of the PM me plz with a price from them..

cheers,

Robbie

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...