Jump to content
SAU Community

Std Rb25det Rebuild

kyle785

By kyle785,
in Engines & Forced Induction

 Share

Recommended Posts

msnismo Grand Master

msnismo

Posted
Posted

perhaps try CP, Arias etc... someone will have some available. I thought ACL did em as they used to have a listing for em.

You may have to adjust the size but it will be cheaper than Nissan OEM

You have the ring sizes obviously?? Just ring around and see if you can get a match...

PRO_32 Proficient

PRO_32

Posted
Posted

Good luck finding aftermarket unless things have changed recently (last two weeks) you can do the ring around and waste your time or you can jjus order genuine nssan rings which btw are cheaper than aftermarket anyway,

Will be 5 to 10 days from japan think last time I paid 280.

Btw standard size is 86mm x 1.2 , 1.5 , 2.8

Hope that helps.

Mandingo Proficient

Mandingo

Posted
Posted
I would use the factory rings if you are keeping the standard original pistons.

Your piston to bore clearances are going to be all whack anyway so there is no need to overcomplicate the process.

  • 2 weeks later...
putraged Rising Star

putraged

Posted
Posted

does anybody know the price comparison for aftermarket rings & OEM rings? i got std size bore forgies going on rebuild next week.

can i use my previous rings? its just 50.000 kms with normal boost anyway, any risk of re-use it?

and also, anybody knows the part number for OEM head stud & main stud for RB25det neo? i've been looking for it, but got no clue at all.

any inputs will be greatly appreciated.

thanks

The Dan Grand Master

The Dan

Posted
Posted
does anybody know the price comparison for aftermarket rings & OEM rings? i got std size bore forgies going on rebuild next week.

can i use my previous rings? its just 50.000 kms with normal boost anyway, any risk of re-use it?

and also, anybody knows the part number for OEM head stud & main stud for RB25det neo? i've been looking for it, but got no clue at all.

any inputs will be greatly appreciated.

thanks

Don't use your old rings. You probably shouldn't be going standard bore either but if it'll hone up to an accurate piston to bore clearance then it'll be ok. Just never seen one come out perfect after 50k though.

Chances are the old rings won't fit the new pistons

Chances are the new pistons come with rings anyway so why would you even consider it?

They don't have studs, they use bolts from factory and Nissan can help you with them.

If you get stuck for a part number and need help ring 07 32907890 and ask for Alan or Joel

The Dan Grand Master

The Dan

Posted
Posted
i have a good faith on my rb25 though. :D:thumbsup:

my forgies are used, so not including rings. anybody know how much set ACL rings cost u?

thanks for the help daniel, i'll call them tomorrow.

ACL Rings cost about $165 a set and can be had from any Repco, Autobarn or other parts stores.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      WGNC34 - floor mats

      By GTSBoy · Posted

      I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • MBS206
      R34 Skyline climate control unit transistor

      By MBS206 · Posted

      Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Murray_Calavera
      Tein Circuit Master- rebuild worth it?

      By Murray_Calavera · Posted

      Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • Duncan
      NC MX5

      By Duncan · Posted

      I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
    • Duncan
      WGNC34 - floor mats

      By Duncan · Posted

      Basically, if there is a part# on the nissan catalogue, it is a genuine part. There is a thing called "new old stock" which is stuff made years ago but never sold (or landfilled), but it is super hit and miss what you can buy. Other than some expensive Nismo stuff there is nothing new being made that suits these cars. The only time to be a little careful is (mostly in the US I think, but maybe Japan too), Nissan started rebranding some cheap crap maintenance parts like oil filters as "Pitworks"; stay away from them, if you are buying cheap just buy whatever the local car parts shop carries The three part numbers have an explanation on Amayama: 0V005 is auto, base style 0V015 is manual 0V505 is auto, hectic momo branded ones, maximum F&F points there!
×
×
  • Create New...