Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

it was a dip with no warning signs that was behind me before i could even say "what the f**k is that."

had another look just now. castor brackets are bent, castor bushes are leaking, cooler core has been bent and damaged a little bit, bottom edge of the cooler and the pipe work has been pushed back about half an inch, exhaust is now a smaller diameter than it was, front guards need the lip hammered back up again (tyre has gone up into the guards, caught on the lip and pulled it back down), leading edge of the sump has taken a small hit but looks fine from the front (if not, kts high cap sump kit here i come), but the rear end and the rails look fine. the castor brackets absorbed most of the impact at the front end.

but yeah, my fault, even though there were no warnings, if i hadve been paying attention to the road instead of my passenger id be right. shit happens.

:) Yep, pretty much, the great bin incident of '08 :)

lol.

probably. but itd be a lot more effort than its worth.

and they could easily come back with 'you were exceeding the speed limit' (not by much, but i was, plain and simple) and 'if your car wasnt so low, it wouldnt have been a problem', which is true. if i had actual ground clearance i wouldve just scraped my exhaust.

Holy crap! Pretty lucky there Dave i'd say!

Oh and Luke, any tricks when fitting or is it pretty straight foreward?

Guess it will be off with the HKS pods then, just for the extra points with the ladies :)

Holy crap! Pretty lucky there Dave i'd say!

Oh and Luke, any tricks when fitting or is it pretty straight foreward?

Guess it will be off with the HKS pods then, just for the extra points with the ladies :(

Piece of piss really, just a tight fit. Handy tip: Fit the AFM's to the box first, then fit the box into the corner, then attach all relevant pipework.

If you need a hand, let me know :)

Piece of piss really, just a tight fit. Handy tip: Fit the AFM's to the box first, then fit the box into the corner, then attach all relevant pipework.

If you need a hand, let me know :(

where are how much did you get your arc box from?

keen to get rid of my pods for one for awhile now but donno where to look for one.

also looking into a bigger sump and oil cooler after i get back from bali.

Edited by Import S13
Will do man, may inlist your help mate, give you a chance to give it a look over too :(

Sounds good mate, just let me know when and I'll be there.

where are how much did you get your arc box from?

keen to get rid of my pods for one for awhile now but donno where to look for one.

also looking into a bigger sump and oil cooler after i get back from bali.

I got mine from someone selling it on NS, managed to pick it up for $450.

As for the bigger sump, the motor will have to come out, a mod I'd love to do on mine but I've always said if the motor comes out, I'll rebuild at the same time

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...