Jump to content
SAU Community

Recommended Posts

yeah the getz will be big nuff to fit it, i mean, i have fit in a washing machine, a four foot fish tank, an arm chair etc etc

i just dont want to dissassemble if dean would rather not

its only 2 bolts on each leg , then 2 bolts holding the hydraulic then 2 bolts holding the arms

narrrrshing strenuous ;D

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Whats a 5stud conversion to a S13 worth? 2nd hand brand new parts whatever,

Cheapest would be bestest for me though wink.gif.

The cheapest route is to get some skyline rear hubs and drive shafts (with the same bolt pattern as your diff ideally) should cost around the $250 mark; and then get some conversion hubs for the front online, these are how i'm getting my conversion hubs from (go the Aussie dollar).

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

$500 from me :/

Only the rear hubs are any good for a 5 stud conversion. S-Series run a McPherson strut front suspension and the skylines runs a double wishbone front end so they aren't interchangeable.

I shall be chasing a CA 5spd conversion soon aswell smile.gif

Just buy my CA 180, it's making 217rwkw ATM and in the next 3 weeks it'll be making at least 235rwkw once i fit the cams i picked up a while ago.

Waynes getting his for like $3k

That's what i was going to sell mine for

Oh well since he has one already organised i guess I'll keep mine for a little bit longer.

EDIT!!

When did i get 1000 posts.

Edited by D_Stirls
The cheapest route is to get some skyline rear hubs and drive shafts (with the same bolt pattern as your diff ideally) should cost around the $250 mark; and then get some conversion hubs for the front online, these are how i'm getting my conversion hubs from (go the Aussie dollar).

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

Only the rear hubs are any good for a 5 stud conversion. S-Series run a McPherson strut front suspension and the skylines runs a double wishbone front end so they aren't interchangeable.

i used s14 front and rear hubs. s14 front lower control arms, and r33 front and rear rotors and calipers. a few years ago that was around $1500 with brand new brake pads.

if u go s14 front and rear rotors and calipers instead of 33. u may be able to get the total cost around $600.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...