Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

you could prob take off in 5th with the 25

and still cane the 20 taking off in 1st :)

ahhhh.... why am i putting a 20 in the 31?

20 can be ok just ask inspect-a-gadget he built a very tough 20 with a worked td05 heaps of custom work in a R31 wagon with 250 rwkw

yer she will be ok for what i need it for.

Fabs32 had a vg30 on his 32, made decent power, and boost come on pretty early, does some

pretty good slides too...

if a full street trim 32 can do it, my stripped 31 can.

Ofcourse the 20 is a good engine, its just easier to start off with the 25/26 because you already have that bit more capacity to make use of. My main motivation for going 25 is because I couldnt find a decent 20 lol (ie. not needing to be rebuilt now or in 6 months)

if a full street trim 32 can do it, my stripped 31 can.

And so will my striped Ceffy. Just need a set of S13 coilovers and a diff that will spin both wheels unlike the one in it now that will spin 2 when it wants to :) and i might need a bigger turbs than a standard 20 cos the turbs on it now seams to run out of puff up in the revs :(

ugh. people shit me.

got my wheels advertised on 3 forums, got a pm on one of them asking me if im willing to sell just the rears for $750...

1) that offer sucks harder than a thai hooker.

2) what the f**k am i gonna do with the front pair? make a f**king coffee table?

Edited by scandyflick
Was walking down hindley around 3am this morning. I see the undercovers 4wd, cops jump out to help with this fight. One guy who was involved in the fight runs off towards me and 5 cops chase after him down hindley. My mate kicks the guy in the leg, slows him down abit, cops still chasing him, tackle him from behind and the guy goes straight to the ground. Everyone cheers.

was this near the lights, i reckon i seen it aswell. only seen some sort of argument from the dude trying to cross the road the car coming through. not sure who was in the right but then he gave his car a boot to the rear quarter. was already dented but the driver seem unhappy about this and went on to finger point for 5min. i figured there wasnt gonna be a fight and went on my merry way. .

also xmas hat got me a pic with a f ing hot blonde who demanded her pic taken with santa :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...