Jump to content
SAU Community

The Sa Wasteland

heslo

By heslo,
in South Australia

 Share

Recommended Posts

DSTROY Grand Master

DSTROY

Posted
Posted (edited)

Just went and had a look at them again, they are from a 32. Rotors are 330 and measured 31mm thick slotted, come with brackets and near new pads with about 15mm of pad on them and braided lines for $2500.

Oh, and they come with a seal kit.

Edited by DSTROY
  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

scandyflick Grand Master

scandyflick

Posted
Posted (edited)
How much bigger/better are F50s compared to 33R Brembos?

piston size there isnt much in it, f50's are 44/40, where gtr's are 44/38 i believe... f40's are the same iirc, 44/38.

funnily enough, the pistons in evo brembos are bigger again, 46/40, but theyre harder to adapt.

the biggest benefit with the f40/50 calipers is the size rotor they can take. bigger rotor = better heat sink.

Edited by scandyflick
scandyflick Grand Master

scandyflick

Posted
Posted
Brakes do my head in. I know nothing.

In even more confusing news! I want to paint my engine covers but have no idea what colour to do them in!

brakes themselves are simple once you wrap your head around the physics involved.

id go bright f**king pink. but thats me.

34R brembo's arnt that good on the track I must admit.

ha. they'd be more than adequate on my car.

scandyflick Grand Master

scandyflick

Posted
Posted

anyone know how much itll cost to have some wheel centres powder coated? im gonna do something with my wheels to pass the time.

and dale, i see you lurking, how many cartons to get a diff reshimmed? mines feeling a little loose, could use a tighten up.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By joshuaho96 · Posted

      From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • MBS206
      Nissan Skyline R34(ER34) Front Suspension Noise

      By MBS206 · Posted

      I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Summernats cruiser?
    • MBS206
      NC MX5

      By MBS206 · Posted

      Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      But if you had to go bury a body in the forest, would you not put that in the boot? Most of them are >=90kg these days.
×
×
  • Create New...