Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

yeah revhead, regional flights are notoriously scary, especially from gladstone, its $161 cheaper if he flew to rockhampton, and thats 107km further north, sometimes i just dont get it. As for the tuning side of things, im hoping to get a tune done thats adequate and safe to drive it to a shop then mark@godzilla can do the hard yards and get me the numbers!

The reply's and suggestions have been great guys, there greatly appreciated!!

Cheers, Allan

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4889762
Share on other sites

Just got mine back now drove it home, seems to run a bit smoother then before. but i was having afm issue and also 02 sensor is playing up so gotta replace that other then these issues its seems to be running ok in the engine dept.

cheers

Daz

Vi-PEC or still stock ecu ?

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4890715
Share on other sites

Vi-PEC or still stock ecu ?

Nah Vipec installed today.

Sorry i mean i was having afm issues before i got the vipec installed and removed them. but the 02 sensor still seems to be another issue i have to address.

P.S. i saw your plates sitting on the snap on tool box today paul! :happy:

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4890719
Share on other sites

Nah Vipec installed today.

Sorry i mean i was having afm issues before i got the vipec installed and removed them. but the 02 sensor still seems to be another issue i have to address.

P.S. i saw your plates sitting on the snap on tool box today paul! :happy:

they drive nice dont they Darren.

yes my car lives in qld...pity i don't

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4890896
Share on other sites

they drive nice dont they Darren.

yes my car lives in qld...pity i don't

seemed to drive better on the way home, but that wouldnt be hard to do after running dodgey air flow meters. lol

but i didnt get it tuned for max power or anything pretty much stocko still at 0.8bar , want to conserve turbos etc till i decide to upgrade. but still have to look into the o2 sensor replacement.

But yeah mark was great to deal with very helpful.

Good bloke.

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4891425
Share on other sites

seemed to drive better on the way home, but that wouldnt be hard to do after running dodgey air flow meters. lol

but i didnt get it tuned for max power or anything pretty much stocko still at 0.8bar , want to conserve turbos etc till i decide to upgrade. but still have to look into the o2 sensor replacement.

But yeah mark was great to deal with very helpful.

Good bloke.

yeah he said he enjoyed working for you...he thought you were a little cautious/sensible...not really the normal customer. Most say turn the boost up...i want a big number etc...you however were patient until you have turbo's upgraded and all the proper support systems in place before turning the boost up. Its a nice safe tune that will look after your hardware till you are ready to take the next step.

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4892422
Share on other sites

yeah he said he enjoyed working for you...he thought you were a little cautious/sensible...not really the normal customer. Most say turn the boost up...i want a big number etc...you however were patient until you have turbo's upgraded and all the proper support systems in place before turning the boost up. Its a nice safe tune that will look after your hardware till you are ready to take the next step.

Yeah just dont see the use of blowing up engine if i dont have to.

and having a garden ornament.

il wait till i can do it properly.

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4892940
Share on other sites

Well, it arrived yesterday! Im about to tackle the ecu install into the factory ecu case over a few rums. Looks the goods, has a good spec sheet and a few people seem to say dam good things about them. Any quick tips before i get insanely frustrated and drink myself into oblivion?

Cheers, Allan

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4896905
Share on other sites

Well, it arrived yesterday! Im about to tackle the ecu install into the factory ecu case over a few rums. Looks the goods, has a good spec sheet and a few people seem to say dam good things about them. Any quick tips before i get insanely frustrated and drink myself into oblivion?

Cheers, Allan

a really hot soldering iron on the factory screws to remove them...dont forget to drill the hole for the vacuum line.

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4896911
Share on other sites

Vi-Pec is in! not so hard. i just double triple double checked everything tho! Now, im at a dilemma, do i sell off stock parts and fund a new set of -5's or do i bite the bullet, go over budget and just buy em or get a set of high flows and hope i can get my goal?? also, can anyone recomend a good...nevermind, ill make a new post. :(

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4899678
Share on other sites

i pulled a power fc out of my rig to make way for the new vi-pec..... much better ecu and i got more power an torque with better driving on the street.

highly recomend.

mercury motorsport installed and tuned my in case ur curious.

so many on here would fail to accept this is actually possible...yes it was hard for them to fathom that something designed, engineered and built this century could actually be better than a similar product from last century.

Engine control is phenomenal...the Vi-PEC made my power fc look like a bucket...but i must admit i used to be an 'FC Fanboi' too.

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4910946
Share on other sites

Heh I'm at the point of doing a fuel system for my T88 powered FD and the power FC is just not up for it.... high impedance injectors only unless you want to run dodgy resistor packs, I'm trying to run the new Siemens 2430cc as secondarys and if I stick with the power FC I'll end up having to use something like an FJO / AEM injector driver

Seriously considering an M800 as that's what my builder uses in his car, but I may explore the VIPEC V88.

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4911321
Share on other sites

hehe

marks just retuned my vipec with my new turbo (hks 2540) and new rb25det (cracked ring in old one) as well as added more goodies in (nismo 740cc's, tomei FPR)

mark is a top guy who gives you the right advice!

hey dirtgarage... is that your greeen/purple (duno what color it is) gtr that is always there.. number plates RH9? if so.. i f**king absolutely adore that car.. that thing is nuts

Link to comment
https://www.sau.com.au/forums/topic/292301-vi-pec/page/2/#findComment-4919824
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • What an awesome idea to fit the facelift Lamborghini Diablo headlights. They are a perfect fit!
    • An update regarding the registration with the DVLA I sent off the paperwork the day after I collected the car from the port, two weeks later it was all returned with a letter explaining they have rejected the application. This was because the cheque was £20 short for the road tax (I used a price list I found online). Nevermind it is what it is, it was sent back to them the following day with a new cheque. Fast forward another 2 weeks or so, I called them for an update to be told it had been rejected. Yesterday (16th September) I received the documents back along with another letter, this time it was because I didn't put an X in one box on the V750 (personalised number plate certificate), which declared that I had the rights to the personalised number plate. Why this wasn't mentioned in the first rejection letter, I don't know, but it could have saved this headache. The documents were sent back today, so fingers crossed third times a charm and it'll FINALLY be registered on the road just in time for the bad weather (woohoo!) To cheer myself up I lowered the front 25mm, was sick of seeing it sit like a monster truck. No idea how much clearance I'll have getting on and off the driveway, I'll worry about that when I can actually drive it
    • You're going to miss not worrying about rust in the strut towers like the Skyline shitboxes out there
    • A few little updates that weren't filmed due to not taking long to do or not interesting enough for their own video. My new K&N Air Filter arrived, I went with an RU-4180 which matched the dimensions of the universal cone filter the car originally had.  The battery had gone flat, while that was charging I tidied up the spaghetti wiring at the bulk head and down the sides of the engine Next job was to swap the stereo The Kenwood harness had the female ISO plugs cut off and the male ISO plugs cut off the adaptor loom and joined with bullet connectors. I ordered in a repair loom through work and re-did it all. New Kenwood unit installed (Android Auto, DAB, Bluetooth, Reverse Camera) The bonnet/hood gas struts have been poor since collecting the car. I couldn't find any suitable replacements locally so took a chance on a pair from AliExpress.  The originals don't use a retaining clip to secure the cup onto the ball fixture, would explain why I struggled for 10-15mins trying to pry off the cups. The ball fixtures unscrew using a 12mm spanner, new ones are the same size. Sadly no photo of them fitted, you're not missing much lol The dished Momo steering wheel got replaced with my Momo Tuner, turns out I ordered counter sunk bolts for the horn trim ring (like they normally are for the steering wheel) instead of allen cap (flat seat)  A terrible photo of a Quaife style gear shift knob I've had stashed in my tool box for many years after purchasing the incorrect thread size (I can see a pattern emerging with ordering incorrect parts...) Also threw in a cup holder and a (empty) Boss Coffee can, because why not  
    • GT-R clearly the better choice! The 300 is certainly not insaly fast but has a decent amount of poke. Does a nice little drift around the corners with a decent amount of throttle. It's VERY predictable in a slide too.  Feels so progressive! People probably presume there's a 25 year old driving it based on my behaviour this week! 🤣
×
×
  • Create New...