Jump to content
SAU Community

Recommended Posts

Hey guys,

I want to further tidy up my engine bay by moving the battery into the boot and use a seal battery. Now my question is how would i connect the positive feed to a 0-4 gauge wire to send to the boot. Anyone with any tips or info it would be greatly appreciated.

Cheers,

Dave

Link to comment
https://www.sau.com.au/forums/topic/292524-battery-relocation/
Share on other sites

run something like this?

http://jaycar.com.au/productView.asp?ID=HC...mp;form=KEYWORD

really depends on the battery connections - you can also get 0 guage eyelet connectors that can be used with the screw in type battery poles.

i use a couple of terminal blocks like that on my 180 (running rear battery).

one on positive one on negative.

have power running directly to a couple of amps where the rear seat used to be, and a 4 gauge running to the front, where i have a distribution block for everything that needs power. the distribution block is shielded off from the rest of the engine bay. it has about 4 or so misc connections in there.

the negative ones run to the amps as well, and also a phat lead directly to the engine. on the engine i have another distrution block, but its bolted right onto the engine. from that comes off a bunch of cables that earth around in places in the engine bay, such as near the injectors, on the chassis, near the fuse/relay box.

to make the distribution blocks for both positive and negative in the engine bay, i used some thick metal (i tihnk it was brass or something), drilled holes through it, and bolted in some decent bolts onto it. the positive block sits in a wicked sweet black perspex box.

the end

i use a couple of terminal blocks like that on my 180 (running rear battery).

one on positive one on negative.

have power running directly to a couple of amps where the rear seat used to be, and a 4 gauge running to the front, where i have a distribution block for everything that needs power. the distribution block is shielded off from the rest of the engine bay. it has about 4 or so misc connections in there.

the negative ones run to the amps as well, and also a phat lead directly to the engine. on the engine i have another distrution block, but its bolted right onto the engine. from that comes off a bunch of cables that earth around in places in the engine bay, such as near the injectors, on the chassis, near the fuse/relay box.

to make the distribution blocks for both positive and negative in the engine bay, i used some thick metal (i tihnk it was brass or something), drilled holes through it, and bolted in some decent bolts onto it. the positive block sits in a wicked sweet black perspex box.

the end

any pics??

heres the Stinger S2488IE Distribution Block i used, sure you wont use all 8 ports but u will use 4 of them

iv never had a problem with it,

i can take piks of mine fitted if you want

http://cgi.ebay.com.au/Stinger-S2488IE-Dis...=item2a02271876

yeah I have pics at home, if I remember I'll post some up. its not the perfect job but it gives you a good idea of whats required etc.

the battery isn't even strapped down in the box :/

thats the next thing i wanted to do.

  • 1 month later...

i see people usually using 0 guage or thicker, i've already purchased 5+ metres of 2 guage for my current car but wont be using it anymore.

so my question is can i use it on a non turbo R32?

Edited by jordan101
i see people usually using 0 guage or thicker, i've already purchased 5+ metres of 2 guage for my current car but wont be using it anymore.

so my question is can i use it on a non turbo R32?

yes 2ga is more then enough. 0ga is overkill

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...