Jump to content
SAU Community

Recommended Posts

Selling my 93 white R32 GTST.

I've had the car for about 3 years which over the time was my pride and joy. It was purchased with 120k on then clock and I have since put another approx 40k on. I replaced the steering rack pretty early on in ownership as it was pretty worn and while I was at it removed the pesky HICAS. The old RB20 was still going strong but I decided when a heater hose failed that it was time for some more torque. With the help of some mechanic mates we bolted the RB25 in and after being professionally wired up it's been going strong for the last 6 months. White the engine was out I replaced a few of the other heater hoses on the 25 and put in some new fuel lines as the others were looking a little tired. Overall the engine bay is now pretty clean and looks pretty stock with painted piping and crinkled rockercovers (I will have photos up tonight).

The body is pretty decent however the paint is pretty average with the clear coat peeling in one spot and it could really do with a new boot. Some other issues with the car are the heater/aircon, horn and rear demister are not working. Given enough time I will organize about getting these sorted however I'm a bit short on time and honestly don't really wanna go to much effort.

The interior has lasted the test of time quite well with only a small bubble in the dash. Overall everything is in pretty much good condition which the exception of the steering wheel and gear knob which I replaced. The old dash cluster globes were pretty dim and one failed so I replaced them with blue reds I bought of SAU a while back.

The car is located in Happy Valley for anyone interested in having a look. I can be contacted via SMS or PM during work hours otherwise feel free to call any other reasonable time on 0438885649

As for price I'm asking 12k ONO and am not really interested in trades but if you're willing to trade a decent amount of cash I might be interested if it takes my fancy. I'm in no real rush here to sell the car but it would be nice to move it on for the right offer before I start spending more on fixing it up.

List of mods:

RB25 DET using RB20 actuator (10PSI) from JIS with under 100k on and new timing belt

FMIC

K&N pod

Turbo back exhaust with split front and highflow cat

Splitfire coilpacks

Bilstein shocks with king springs (as per Sydneykid group buy)

Whiteline sawybars front and rear

HICAS removed with lockbar

ISC Alum radiator with silicon hoses

Exedy HD clutch

Bendix ultimate pads

MOMO Race steeringwheel

Nismo leather knob

Apexi EL boost gauge

Replaced gear and handbrake boot

Alpine MP3 headunit

Soundstream splits and amp

Sub out of a Krix HT sub (yay for contacts)

Dynamat in front doors

Darkest legal tint

Alarm and imob however alarm siren died :cool:

Plenty of receipts which make me cry and I'm sure I've missed some thing. Got a few spares in the shed for any potential owner.

I will be uploading some more pics tonight and if there is anything in particular you'd like to see feel free to contact me.

Here's some pics I have on my work PC however I have sold the Drifteks so It will just be on the stock 16 like below:

16052009177-1.jpg

385839602_l.jpg

Link to comment
https://www.sau.com.au/forums/topic/292580-r32-gtst-with-rb25-sa/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...