Jump to content
SAU Community

Recommended Posts

Hi, I am willing to buy a fast car, but I prefer a hot hatch..

My shortlist are: Colt Ralliart, 206 GTI 180, Polo Gti or a Corolla Tivo..

I like a car with lots of torque in not so high rpm, a great "dancer" and still be able for a daily commuter with high quality and cheap parts, but I dont think that I will modify my car..

Which one is the best for me? Or do you guys have other ideas?

Thanks..

Link to comment
https://www.sau.com.au/forums/topic/294215-hot-hatch-17k/
Share on other sites

count the rolla out then, no torque and need to rev it hard to get it going..

colt ralliart's look gay but still decent power + you get the awesome mitsu warranty..

dont know much about the 206 or the gti performance wise but id say parts would be more expensive than the corolla..

Link to comment
https://www.sau.com.au/forums/topic/294215-hot-hatch-17k/#findComment-4909609
Share on other sites

VW 9N Polo GTi + ECU reflash + rear sway bar = finished

No external mechanical mods means the cops will not be able to find anything to defect you for (and being un-Japanese you won't get as much cop attention in the first place). The thing pulls across most of its rev range and makes really good power for the weight with that reflash. Even when the car's serviced, they might not notice. There's a mode to set the ECU back to stock anyway.

The rear sway bar will dial out a lot of the "OEM safety" understeer, while not making it scarily taily.

Link to comment
https://www.sau.com.au/forums/topic/294215-hot-hatch-17k/#findComment-4910062
Share on other sites

Aaaah Dr Tony!!!!

Welcome to the BEAR PIT !!!! SAU Bear Pit that is !!!!!!!

Aren't your exams coming up soon ?????

hey terry.

bear pit? lol

yeah exams in like 2 weeks. 1 week left of being a medical student (finally!!!) and i should know everything! hahaha.. not really stressing, coz i should know everything now to be a safe dr...well i hope so. lol

anyways, back on topic...

yeah true, MPS 3 is expensive. didnt realise the 17k +/- in the title....but its still hot, and if u want torque, theyre like torque monsters. too bad its FWD...

Link to comment
https://www.sau.com.au/forums/topic/294215-hot-hatch-17k/#findComment-4911781
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...