Jump to content
SAU Community

Recommended Posts

the problem: less coolent in radiator after drive,I need top up everytime when engine is cool(about 250ml sometime more sometime less). the coolent in overflow bottle is getting more and more. so thats mean: coolent flow to overflow bottle when hot, but when cool down the coolent not fully go back to radiator. i did some record. the coolent still go in to radiator when cold but not as much as the coolent from radiator to overflow bottle when hot. say coolent from radiator to overflow bottle 500ml when hot, when its cool down the coolent only come back to radiator 250ml.

I went to a few place to check the cooling system. all good. no problem at all. all of them suggest me try to change a cap.

then I bought a new radiator cap(1.3bar), nothing changed.

but my car never overheat always 75-85degree on PFC. can i just drive like this? don't need really care about it??? I worried the coolent in radiator will getting less and less during time.

I got arc radiator and nismo cap.

car is r34gtr.

anyone help please!!!

the fact that if isn't drawing coolant back into the radiator suggests there is something wrong. if you have a new cap, then i would be looking at the overflow bottle or the hose to the overflow bottle. there may be a small amount of debris at the bottom of the overflow bottle that is allowing the coolant to come in, but when it tries to suck it back in it is blocking up the hole and not letting it back in.

If it's not the cap then it is likely the tube running form radiator overflow or quite possibly the nipple on the radiator. My thoughts are that the force of fluid coming out of the radiator when hot is high but the force under vacuum for refilling when cold is low. The hole might have corroded or the hose is partially blocked.

The hole in my aluminium radiator was blocked from a little bit of crap, I just scraped it out with a drill bit.

First thing to do is to look for coolant stain's over your engine block, top of gearbox at rear, around hoses ect, my next thing would be respective of head gasket or turbo seals.

its still about 150ml coolent less in radiator. the coolent should be full in radiator no matter engine burn water or not is that right?? if the engine burn water the coolent in overflow bottle should getting lower not the coolent in radiator?

PS: I have nismo water pump

Edited by Nosure
if the motor is using coolant it will use it from the radiator first then the overflow.

either you have a small leak which is only evident under pressure or you have a headgasket issue.

even the engine using some coolant does the radiator should still full? and the overflow should get less coolant?

the radiator should always be full. The overflow bottle is an expansion chamber basically when the coolant is hot, it expands and some is pushed to the overflow bottle and then taken back into the radiator once cool.

what you need to do, is fill the rad with bleed screw on the manifold taken out til the system is full. then reseal the system, make sure the overflow bottle is filled to the MAX line and then mark it.

drive for a few days and then re check it.

if you have lost coolant from either the rad or the overflow then you either have a leak or a gasket problem, simple as that

better way to bleed system. leave your cap and cock on the top of your manifold off, run the car up to op temp and let all air in the system bleed out thoroughly.

making sure your overflow is half full?

the radiator should always be full. The overflow bottle is an expansion chamber basically when the coolant is hot, it expands and some is pushed to the overflow bottle and then taken back into the radiator once cool.

what you need to do, is fill the rad with bleed screw on the manifold taken out til the system is full. then reseal the system, make sure the overflow bottle is filled to the MAX line and then mark it.

drive for a few days and then re check it.

if you have lost coolant from either the rad or the overflow then you either have a leak or a gasket problem, simple as that

thanks mate but where is the bleed screw?? and how can I do it?? some more detail please

better way to bleed system. leave your cap and cock on the top of your manifold off, run the car up to op temp and let all air in the system bleed out thoroughly.

making sure your overflow is half full?

OK I will try it. thanks mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey guys, Just want some advice on r34 GTT ac system. Since I’ve owned it, the ac compressor, doesn’t matter the set temperature or ambient temperature, runs for around 10 seconds then disengages the clutch, then re-engages everywhere 30 seconds or so and keeps repeating this.    is this normal?   I had it recharged today as it was slightly low and thought it would fix it but still does it. it cools fine in summer even prior to the recharge, except for the usual warmup when stopped or in traffic (still yet to wire overheat fan to on with ac)   any thoughts would be much appreciated 
    • To plug the hole. The engine plant may not have known whether the car it was going into had a gauge or not. It was a long time ago and the integrations might not have been fully modern. Or they might not have cared because the extra inventory and processes to save a few cents on the sender might have cost more anyway. But please tell me you are not still confusing the idea of a pressure gauge sender, and an oil pressure light switch. The switch will be out there. In a separate hole. Probably with only one wire running to it. Running the light.
    • Blower needs to go low on the exhaust side, displacing the AC and PS, which you have to decide whether you want to keep and how and where to relocate if you do. Electric option for PS is, at least, helpful. Sadly, there is no workable 12V electric AC of any value. Whilst the blower is the last compression step before the throttle, and so it might seem a good idea to have it near the inlet manifold (as mentioned above), you probably want it to go through an intercooler first, so, having it on the opposite side of the car facilitates that air flow path. The turbo discharges into the blower, so proximity of the turbo's compressor outlet to the blower's inlet is nice. But then you might want to intercool that too, before boosting it again....which would probably be a ball ache. Routing pipes out to the front and back could be a bit shit. If there was room for (at least) a small (but preferably larger) water to air core on that side, then that would probably be the best approach. I guess a reasonable alternative would be to locate the blower where the alternator is (more or less, associated with the inlet manifold, per Matt's thought), and somehow incorporate a water to air core into the manifold, sort of like they do for modern blown V8s. The big difference here though is that those V8s have only the one throttle (upstream the blower) and only the one compression step (the blower) and no need for too much in the way of bypass/blowoff valves. Whereas in a twin charged 6, you do need to think about one or two bypass valves associated with the 2 compressors and you would prefer to have the intercooling done before the air has to pass through the throttle. You'd like the throttle to work approx the same no matter what the compression is doing. But if it is located in hot air stream before a cooler, then sometimes the air will be real hot, sometimes it will be quite cool, and the throttle mapping/response will be quite different between those two cases. The throttle, if sized for hot air, would be too large for cold conditions. It's all a ball ache.
    • Package SC on exhaust side. Remote mount turbo. Still a fair bit of room when you get creative on the inlet side of the motor too. Especially if you can get really creative with the welding, and effectively build it into the bottom of the inlet manifold. Would definitely take some design work, and some trial and error, to make sure flow works well still! Might be easier to just start with the Nissan March though... All the work is already done for you...
×
×
  • Create New...