Jump to content
SAU Community

Recommended Posts

Hey there peeps.

I think I've decided on Bilstein shockies for my 34 because I can lower the ride height without needing new springs, which also means I keep the progressive rate of the standard springs = comfort when cruising but firmness when cornering hard (to my knowledge).

My question is; am I going for the sport version or the comfort version?

And how much have people been paying for these? I was quoted $1k for all four but I didn't ask or get told whether this was for sport or comfort.

Thanks in advance for your comments.

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/
Share on other sites

Bilsteins are Bilsteins - AFAIK, they don't come in different 'comfort settings' (although you might be able to have them custom valved).

Shocks are there to control the springs. The springs are what supports the car, and what gives comfort (or lack of it) in the ride. It could be that the standard springs will be too soft for the Bilsteins. I have Kings in my R32 GTS4, rated around 280 lb - Quadrant here in Melbourne recommend something like 430 lb springs for their Bilsteins to suit a R32 GT-R.

If you want cornering, you fit sway-bars.

I got a set for the GTS4 for around $1k, so the price you have been quoted sounds about right.

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/#findComment-601819
Share on other sites

Ah thanks for that. I just realised that it was the Bilstein Hot Rod shocks that come in comfort and sport. I read the thing wrong.

I have been told that the Bilsteins will last 50k with the standard springs and this persons opinion was that it was worth it for the comfort factor.

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/#findComment-601855
Share on other sites

Bilsteins like all hydrualic devices, have velocity sensitive valving so they accept a wide range of spring rates. They are also multi valved in both compression and extension, so they damp an even wider range of spring (and velocity rates) then single or dual valve shocks. Unlike some things in life you do get more for your money when you buy a decent shock absorber.

Bottom line, off the shelf Bilsteins will work just fine on standard springs and accept the usual 20% to 25% upgrade in spring rates you get with lowered, off the shelf sports springs. Obviously competion rates are a different matter, where revalving is always required.

Hope that helps

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/#findComment-606938
Share on other sites

again sydneykid comes thru with the goods!

I actually just bought a set of these bilsteins, SPORT model, as sold by UAS, and cost me easily under a grand. I think they sell them for 920$ a set but i got them a bit cheaper.

As for the springs, im running Kings lows (progressive rate rears) and Kings quote them as 180lb fronts and 175lb rears, and i had them spring tested just to confirm. I also tested my std springs for comparison and i think they were around the 140lb mark, so the kings are about 25% firmer.

Before i ordered the bilsteins i spoke to the aus distributor for bilsteins and the guy was happy when i said i was using kings springs, and that they would be an excellent match.

Blind elk, 280lb in your kings is higher than the usual for them, did you have them custom made at that rate? As for street that is very firm.

Also 430lb springs is VERY firm, too firm for street unless you like drift style- the teins in my car at the moment are over 400lb and unless the road is good, its very bumpy. UAS recommend UP TO 400lb springs for their 300zx track car.

-i pick my shocks up tomorrow, when i get them in ill put up a review.

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/#findComment-607336
Share on other sites

Abo Bob, i did a fair bit of reading and research before buying my bilsteins, and the sport shocks are described as 'firm', but also something bilstein describe as 'self-adjusting', and work well with the progressive rate springs, and maintain a certain amount of comfort at the same time.

I also looked at KYB shocks as used in HPI's R34, the externally adjustable ones, and the bilsteins are meant to be better for the money, and apparently you dont need the adjustability in a street setup for these shocks with std/upgraded springs.

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/#findComment-607356
Share on other sites

  • 2 weeks later...

Hi guys it always amazes me how people avoid gettting their wheel alignment checked. I check the race cars' alignment every time they go out. It is so important to how your car handles and drives and it can save you way more than the cost in tyre wear alone.

It is unbelievable the number of times I have seen cars with $000's spent on springs and shocks that handle badly because their suspension geometry is all over the place.

My 20 cents worth Sly33, get it wheel aligned.

Link to comment
https://www.sau.com.au/forums/topic/29429-bilstein-shockies/#findComment-621663
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Nah, don't bother doing any actual measurements on the car. Just go ask the inter-f**king-net.
    • I currently have 18 x 9 +30 on the front with 18 x 10.5 +38 on the rear. Absolutely regretted it. Ended up putting 15 mm spacers on front and 25 mm spacers on the rear. Not to mention the rears were like a mm from hitting the coilovers. Definitely would go more aggressive then what you were originally planning. Keep in mind my guards are rolled and cars fair low so you might possibly need to roll guards depending how aggressive you go and how low the car is. Im not an expert but the 18 x 8.5 +25 18x9.5 +30 Sounds like it would sit much better.
    • Hey guys, sorry i have been researching for a few months and absolutely cannot wrap my head around this. I am about to order some rims to fit my R34 Gtt with coilovers My original plan was to order Rota grid R in 18x8.5 +30 235 40 R18 Fronts 18x9.5 +35 255 35 r18 rears But then the thought in my head said this isnt aggressive enough. I want the most concave spokes i can get without too much of poke and scrubbing   So my thoughts now is  18x8.5 +25 18x9.5 +30   My question is will this be the most aggressive i could get it without any guard rolling and does the type of rim style affect the offset / size.   Thanks everyone.
    • Lower parts are there. On passenger seat, bright yellow bit is the release mount. On drivers, bright yellow bit is the lower buckle for the other side. My bet is lowers are tucked out of the way as much as possible for visuals.
    • I'm guessing its a 4 point harness, 3 of the 4 belts are visible. I'm guessing the hidden belt is tucked down between the seat and door. 
×
×
  • Create New...