Jump to content
SAU Community

Recommended Posts

location: Perth

0405 255 824

willing to freight interstate at buyers expense

----------------------------------------------------------------------------

18" R34 GTR rims

they have been professionally powdercoated in a gloss black.

they do not come with the centrecaps.

theres the occasional scratch and stuff, but nothing serious.

theres a bit of rash (minimal), but was powdercoated over, so its impossible to notice

$2100 ono

rims:

18x9"

+30 offset

tyres:

235/40/R18 Nexen N6000s, not road legal.

2cep8j4.jpg

2209091618.jpg

----------------------------------------------------------------------------

17" R34 GTT rims

$500 ono

good condition, few little scrapes here and there on the rims

comes with 4 centrecaps

tyres: 225/XX/R17

3 are 1mm above the tread wear indicator

1 has heaps more (looking like 70% tread) on it.

2s76znq.jpg

2hcf3wm.jpg

----------------------------------------------------------------------------

17" Buddy Club P1s

$1100 ono

rims:

17x8 +37

17x9 +42

they have a couple of scratches and nicks, but nothing serious.

tyres:

fronts, 225/XX/R17, have camber wear, but seem legal, will have to double check

rears, 235/45/R17, around 1 to 2mm above the tread wear indicators

0311091450.jpg

yeh had to get the hub bored out a tiny bit.

but its still good for skyline, it located well on the hub on my 32

Edited by Tocchi
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...