Jump to content
SAU Community

Recommended Posts

S15 PARTS

s15 camber arms $20

s15 rear parcel shelf $40

s15 genuine veilside rear bar make a offer i need it gone

s15 adm passenger sunvisor $10

s15 washer bottle $10

s15 overflow bottle $10

s15 eyelids paint black with glitter $50

s15 drivers side under dash bit $20

RB26 PARTS

r32 rb26 coilpacks $30 each

rb26 timing belt only 8000kms old genuine nissan $20

rb26 flywheel $30 will also fit rb20 rb25

r32 rb26 dump pipes with 02 sensors $50 pair

rb26 baffle plates (bolt to bottom of engine) $30

rb26 alloy engine brackets $30

R33 GTST PARTS

r33 gtst gearbox crossmember will fit r32 r33 s13 s14 s15 $20

r33 gtst manual brake pedal $20

r33 gtst manual clutch pedal $20

r33 rb25 rear tailshaft $30

r33 radiator brackets $5

rb25 rb20 rb26 starter motor low kms $30

R32 GTST PARTS

r32 gtst manual brake pedal $20

r32 gtst boot seal $30

r32 under dash drivers panel $15

rb20 cam gear cover $20

r32 washer bottle $10

r32 overflow bottle $10

r32 drivers side electric window thingy $15

MISC

drift 3 inch stainless air filter $20

4 inch canon $20

5 inch canon $40

boost tee $10

kenwood 4 channel amp $70

LOCATED ON THE GOLD COAST BUT WILL POST.

BRAD 0421511710

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...