Jump to content
SAU Community

Anybody Experienced Leaked In There Itb Shaft?

andy95'R33GTR

By andy95'R33GTR,
in Engines & Forced Induction

 Share

Recommended Posts

andy95'R33GTR Rising Star

andy95'R33GTR

Posted
  • Author
Posted (edited)

assembled already, and first start, idle seems high, according to my safc, idle is 1200rpm is this high idle? AAC is already full adjusted, cannot lower the idle anymore

Edited by andy95'R33GTR
J'z-R33 Grand Master

J'z-R33

Posted
Posted

Did you clean the inside of the TB's before you put them back in? more importantly did you remove the thin layer of black silicon from around the TB flange? if you did you will need to reapply this.

There is a DIY somewhere on here..

andy95'R33GTR Rising Star

andy95'R33GTR

Posted
  • Author
Posted

i read those post...and so thats why i did not clean my my throttles, and i have a safc, air flow is 1.1 throttle position is 0 still, but i haven't run the car for long yes, maybe it needs for heat to lower the idle?

andy95'R33GTR Rising Star

andy95'R33GTR

Posted
  • Author
Posted

adjusted the ecu to full counter clockwise... rpm 1170 with a/c 950, is this normal??? bov still not working when i run and tested, when i feel the vacuum of the bov, i can feel the vacuum pressure but when i rev the engine, the pressure is pushing air not vacuum pressure, is this normal? please

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...