Jump to content
SAU Community

Recommended Posts

hey guys i recently purchased from a wreckers a stock intercooler pipe, i asked for the pipe that goes from the turbo outlet to the intercooler but i dont think i got the pipe i asked for

ive been looking for pics but havnt found any

i think ive got the pipe that goes from the crossover pipe to the intercooler by mistake, if anyone could post up a pic it would be great

below is the a tiny picture of pipe i outlined with the red arrow

just need a pic of it say out of the car so i can see the bends and all and compare it to the pipe i was given

thankyou

post-36737-1258266600_thumb.jpg

Edited by adoboy666
heres the pic of the pipe i have

that ain't the stuff.

i reckon this is what u need - im not 100% sure if this is the one you are after because there are a few pipes and bends but this is one of them.

post-36583-1258273267_thumb.jpg

Edited by sonoramicommando
that ain't the stuff.

i reckon this is what u need - im not 100% sure if this is the one you are after because there are a few pipes and bends but this is one of them.

ok looked thru a few more photos. i think i got it wrong - the photo i upload is from intercooler outlet.

the pipe you have the arrow on, it's a short 90° bend, which goes down to intercooler inlet with a rather longish joiner, assuming you have a stock cooler. with a front mount (like the photo you have), you probably need some more pipes I guess.

post-36583-1258274494_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...